Agilent N1913A and N1914AEPM Series Power MetersConsistent results and greater capabilityData SheetDo more with new-generation EPM power meters Get u
10E-Series power sensor specificationsThe E-Series of power sensors have their calibration factors stored in EEPROM and operate over a wide dynamic ra
E-Series CW power sensor specificationsThe chart in Figure 1 shows the typicaluncertainty in making a relative powermeasurement, using the same power
12E-Series E9300 average power sensor specificationsThe E-Series E9300 wide dynamic range, average power sensors are designed for use with the EPM fam
Typical SWR, 10 MHz to 18 GHz (25 °C ±10 °C)for E9300H and E9301H sensors13E-Series E9300 average power sensor specificationsTypical SWR, 10 MHz to 18
Typical E9300H/01H power linearity at 25 °C, after zero and calibration, withassociated measurement uncertaintyPower range26 to 20 dBm20 to 10 dBm
15E-Series E9300 average power sensor specificationsEffects of change in temperature on linearityNote: If the temperature changes after calibration an
16E-Series E9300 average power sensor specificationsSwitch point dataThe E9300 power sensors have two paths asshown in Table 7. The power meterautomat
17E-Series E9300 average power sensor specificationsTable 12b: Calibration factor uncertainties (high power path)Frequency10 MHz to 30 MHz30 MHz to 50
188480D Series diode and 8483A thermocouple power sensor specificationsCalibration factor uncertaintiesThese thermocouple and diode power sensors prov
198480D Series diode and 8483A thermocouple power sensor specificationsMaximum SWR and power linearityTable 14: 8480 Series maximum SWR and power line
Take a closer lookN1914A front panelN1914A back panel2Rear-panel sensor and PowerRef connectors provide anoption to replace front-panelconnectorsDC re
20N8480 Series thermocouple power sensor specificationsThe N8480 Series power sensors (excluding Option CFT) measure power levels from 35 dBm to +44
21N8480 Series thermocouple power sensor specificationsMaximum SWR and power linearity for standard N8480 Series power sensorsTable 16: N8480 Series m
22N8480 Series thermocouple power sensor specificationsSwitch point dataSwitching point is applicable for standard N8480 Series power sensors only.The
23U2000 Series USB power sensor specificationsThe U2000 Series USB power sensors are true average, wide-dynamic-range RF/microwave power sensors, base
24U2000 Series USB power sensor specificationsMaximum SWRFor more detailed specifications,refer to theAgilent U2000 Series USB power sensorsdatasheet
www.agilent.com/find/emailupdatesGet the latest information on theproducts and applications you select.www.agilent.com/find/agilentdirectQuickly choos
N1913A/14A Series power meter: applications and compatible sensors for averagepower measurementsMetrologylabPulse/averagedRadar/navigationModulatedWir
4Specifications describe the instruments warranted performance and applyafter a 30 minute warm-up. These specifications are valid over itsoperating/e
51. Settling time: 0 to 99% settled readings over the GPIB2. When a power step crosses through the sensors auto-range switch point, add 25 ms. Refer
N1913A/14A EPM Series power meters performance characteristicsSettling time (continued)Auto filter, 10 dB decreasing power step for normal and X2 mode
7N1913A/14A EPM Series power meters performance characteristicsRear panel connectorsRecorder outputs: Analog 0 to 1 Volt, 1 kW output impedance, BNC c
8N1913A/14A EPM Series power meters performance characteristicsOperating environmentTemperature: 0 °C to 55 °CMaximum Humidity: 95 % at 40 °C (non-con
9N1913A/14A EPM Series power meters ordering informationPower metersN1913A: Single-channel average power meterN1914A: Dual-channel average power meter
Comments to this Manuals