Agilent Technologies 6201B User Manual

Agilent E4990A Impedance Analyzer20 Hz to 10/20/30/50/120 MHzData Sheet

10Impedance measurement accuracy at four-terminal pair portEquation 1 shows the impedance measurement accuracy [%] at four-terminal pair port of the E

11Zsl []0 m: 0 1 m (16048G), 2 m (16048H): 20 Hz ≤ fm < 500 Hz: 5 m 500 Hz ≤ fm ≤ 120 MHz: 2 mKbwMeas Time 5: 1 Meas Time 4: 1 Meas Time 3: 3 at ≤

12Figure 5. Impedance measurement accuracy at four-terminal pair port of the E4990A's front panel (Oscillator level = 0.5 Vrms), measurement time

13Impedance measurement accuracy at 7-mm port of the Agilent 42942AEquation 2 shows the impedance measurement accuracy [%] at 7-mm port of the 42942A

14Yo [S]20 Hz ≤ fm < 100 Hz: 100 n 100 Hz ≤ fm ≤ 200 kHz: 25 n1 200 kHz < fm ≤ 1 MHz: 50 n1 1 MHz < fm ≤ 120 MHz: 5  f/100 + 50 n1Zsl [] 0K

15Figure 6. Impedance measurement accuracy at 7-mm port of the Agilent 42942A terminaladapter connected to the E4990A (Oscillator level = 0.5 Vrms), m

16Impedance measurement accuracy at test port of the Agilent 42941AEquation 3 shows the impedance measurement accuracy [%] at test port of the 42941A

17Yo [S]20 Hz ≤ fm < 100 Hz: 100 n 100 Hz ≤ fm ≤ 200 kHz: 25 n1 200 kHz < fm ≤ 1 MHz: 50 n1 1 MHz < fm ≤ 120 MHz: 20  × f/1001Zsl [] 0KbwMe

18Figure 7. Impedance measurement accuracy at test port of the Agilent 42941A impedance probe connected to the E4990A (Oscillator level = 0.5 Vrms), m

19Limit Line TestDisplay FunctionDisplay Size/type 10.4 inch color LCD (TFT) Number or pixels11024 X 768 (XGA)Scale type X axis scale Linear and

2DefinitionsSpecification (spec.): Warranted performance. All speciications apply at 23 °C (± 5 °C), unless otherwise stated, and 90 minutes after the i

20Handler interface Connector type 36-pin centronics, femaleSignal type Negative logic, opto-isolated, open collector outputPin location See the follo

21Table 1. 24 bit I/O port pin assignmentPin No. Signal Name Signal Standard1 GND 0 V2 INPUT1 TTL level, pulse input, pulse width: 1 s or above3 OUTP

22Analyzer Environmental SpecificationsMeasurement circuit protectionMax discharge withstand voltage11000 V @ C < 2 F, √(2/C) V @ C ≥ 2 FNOTE: Dis

23General CharacteristicsExternal reference inputFrequency 10 MHz ± 10 ppm (Typical)Level 0 dBm to ± 3 dB (Typical)Input impedance 50  (nominal)Conne

24EMC, safety, environment and complianceEMC European Council Directive 2004/108/ECIEC 61326-1:2005EN 61326-1:2006CISPR 11:2003+A1:2004EN 55011:2007Gr

25Safety European Council Directive 2006/95/ECIEC 61010-1:2001 / EN 61010-1:2001Measurement Category IPollution Degree 2Indoor UseCAN/CSA C22.2 No. 61

26Dimensions, weightWeight 14 kgDimensions See Figures 10 through 12Figure 10. Front view (Millimeters)

27Figure 11. Rear view (Millimeters)Figure 12. Side view (Millimeters)

myAgilentwww.agilent.com/find/myagilentA personalized view into the information most relevant to you.www.lxistandard.orgLAN eXtensions for Instruments

3Voltage Signal LevelCurrent Signal LevelRange 5 mVrms to 1 VrmsResolution 1 mVAccuracy at four-terminal pair port of the E4990A or 7-mm port of the 4

4Output impedance 25 Ω (nominal)Signal Level MonitorOutput ImpedanceVoltage range (Same as the voltage signal level setting range)Voltage monitor accu

5DC Bias FunctionDC voltage bias Range 0 to ± 40 V (see Figure 1) Resolution 1 mV Accuracy ± [0.1% + (5 + 30 × |Imon|) mV]± [0.2% + (10 + 30 × |

6Sweep CharacteristicsAvailable sweep parameters Frequency, signal voltage, signal current, DC bias voltage, DC bias currentSweep type Linear frequenc

7Measurement TimeFigure 2. Measurement time (Option 120, adapter: None, 1 m, 2m, Typical)Figure 3. Measurement time (Option 120, adapter: 7mm 42942A/p

8Adapter SetupCalibrationAdapter selection NONE No adapter (the 16047E, etc. direct connection type test fixture is connected) 4TP 1M Four-terminal

9Measurement AccuracyConditions of accuracy specificationsTemperature Four-terminal pair port of the E4990A’s front panel23 ± 5 °C Beyond 23 ± 5