Agilent Technologies n3306a User Manual Page 51
- Page / 102
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4 - Turn-On Checkout
54
6.
Depress the Meter key followed by
the scroll key.
1 50 W The display shows the computed input
power for the selected channel.
7.
Repeat steps 3 through 6 for any
other modules in the mainframe.
8.
Turn off electronic load, disconnect
power supply and continue with
rear panel connections.
NOTE: If the Err annunciator on the display is on, press the Shift key followed by the Error key to see
the error number. See Table 4-2 for a list of errors.
In Case of Trouble
Error Messages
Electronic load failure may occur during power-on Selftest or during operation. In either case, the display may
show an error message that indicates the reason for the failure.
Selftest Errors
Pressing the Shift, Error keys will show the error number. On the front panel, selftest error messages appear as;
ERROR <n> where "n" is a number listed in the following table. Some values consist of a number followed by
the affected channel. If this occurs, turn the power off and then back on to see if the error persists. If the error
message persists, the electronic load requires service. Refer to the list of Agilent Sales and Support Offices at
the back of this manual.
Table 4-2 Selftest Error Codes
Error Failed Test
0 No error
2 Non-volatile RAM CONFIG section checksum failed
4 Non-volatile RAM STATE section checksum failed
5 Non-volatile RAM RST section checksum failed
10 RAM selftest failed
11<channel> CVDAC selftest 1 failed on specified channel (01 - 06)
12<channel> CVDAC selftest 2 failed on specified channel (01 - 06)
13<channel> CCDAC selftest 1 failed on specified channel (01 - 06)
14<channel> CCDAC selftest 2 failed on specified channel (01 - 06)
15<channel> CRDAC selftest 1 failed on specified channel (01 - 06)
16<channel> CRDAC selftest 2 failed on specified channel (01 - 06)
17 ADC buffer failed
18<channel> LIMIT section checksum failed on specified channel (01 - 06)
19<channel> CAL section checksum failed on specified channel (01 - 06)
20 Input Down
40 Flash write failed
42 Flash erase failed
80 Digital I/O selftest error
- USER’S GUIDE 1
- Warranty Information 2
- Safety Summary 3
- Declaration Page 5
- Acoustic Noise Information 6
- Printing History 6
- Table of Contents 7
- The Front Panel -At a Glance 10
- U Power cord 11
- V Trigger/Digital 11
- W Sense switch 11
- Front Panel Number Entry 12
- Front Panel Annunciators 13
- Immediate Action Keys 13
- Quick Reference - 1 14
- 1 - Quick Reference 15
- Front Panel Menus - continued 15
- SCPI Commands - continued 17
- General Information 18
- Safety Considerations 19
- Options and Accessories 19
- Description 19
- Features and Capabilities 20
- Front Panel Controls 20
- Remote Programming 20
- Operating Modes 21
- Constant Resistance (CR) Mode 22
- Constant Voltage (CV) Mode 23
- Transient Operation 25
- List Operation 26
- Triggered Operation 26
- Input Control 29
- Protection Features 29
- Saving and Recalling Settings 32
- External Control Signals 32
- Input Measurements 33
- DC Measurements 34
- RMS Measurements 34
- Power Measurements 34
- Measurement Ranges 34
- Installation 35
- Installing the Modules 36
- Channel Number 37
- 3 - Installation 38
- Bench Operation 39
- Rack Mounting 39
- Input Connections 40
- Wire Considerations 42
- Control Connector 44
- Sense Switch 45
- Computer Connections 46
- 1 2 3 4 5 46
- 6 7 8 9 46
- Application Connections 47
- Figure 3-11. Remote Sensing 48
- Low Voltage Operation 49
- Turn-On Checkout 50
- In Case of Trouble 51
- Front Panel Operation 52
- Function keys 55
- Scrolling Keys 56
- Metering Keys 56
- Input Control Keys 57
- Transient Control Keys 58
- Trigger Control Keys 58
- List Control Keys 58
- Entry Keys 59
- 5 - Front Panel Operation 61
- 4 - Programming Lists 64
- 1 2 3 4 5 65
- List Count = 1 List Count = 2 65
- 7 - Setting the GPIB Address 67
- Specifications 68
- A - Specifications 69
- Specifications - A 70
- Introduction 72
- Equipment Required 72
- Performance Tests 73
- CV Mode Tests 74
- CV Mode Regulation Test 75
- CR Mode Tests 76
- Pulse Width Accuracy 79
- IMON_INV 85
- Calibration 87
- VOLTAGE Calibration Program 92
- Manual Updates 102
Related products and manuals for Measuring, testing & control Agilent Technologies n3306a
(320 pages)© 2020, manymanuals.com. All rights reserved. | 1.548 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals