Agilent Technologies 8922M User's Guide Page 84
- Page / 384
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-6
AF Analyzer Subsystem
FILTer1
FILTer1
Description Selects/queries the AF Analyzer Filter 1.
Syntax AFANalyzer:FILTer1?
AFAN:FILT1?
AFANalyzer:FILTer1 <string>
AFAN:FILT1 <string>
Options ‘20HZ HPF’ | ’50HZ HPF’ | ’300HZ HPF’
FILTer2
Description Selects/queries the AF Analyzer Filter 2.
Syntax AFANalyzer:FILTer2?
AFAN:FILT2?
AFAN:FILT2 <string>
AFANalyzer:FILTer2 <string>
Options ’300HZ LPF’ | ’3KHZ LPF’ | ’15KHZ LPF’| ’>99KHZ LP’
GTIMe
Description Sets/queries the AF ANalyzer Gate TIMe (AF Cnt Gate).
Default GPIB unit is seconds (S).
Default display unit is milli-seconds (MS).
Syntax AFANalyzer:GTIMe?
AFANalyzer:GTIMe <real [units]> | [:FNUM]
Options Refer Appendix B.
- Programming Reference Guide 1
- Contents 10
- Command Guidelines 17
- Command Names 18
- Units of Measure 20
- Measurement Subsystems 21
- Syntax Diagrams 21
- Optional Commands 22
- Command Descriptions 23
- Command Name 23
- Averaging 24
- GPIB Tutorial and Examples 25
- GPIB Programming Exercises 26
- Originate a Call 27
- End the Call 27
- TX Level Changing 28
- ARFCN Changing 29
- TX Power Measurement 30
- DSP Measurements 31
- Receiver Sensitivity Test 33
- Example D - Adding Robustness 35
- Example E - Faster Testing 36
- Commands used in exercise A: 38
- Commands used in exercise B: 38
- Commands used in exercise C: 39
- Example Programs 40
- Test List 41
- Sample Output 42
- Program 1 43
- Program 2 53
- Program 3 64
- Transient Settling Times 74
- AF Analyzer Subsystem 79
- DEMPhasis 82
- DEMPhasis:GAIN 82
- DETector 82
- DETector:PKLocation 83
- DETector:SETTling 83
- ELResistor 83
- INPut:GAIN 85
- NOTCh:GAIN 85
- SPEaker:MODE 86
- SPEaker:VOLume 86
- AF Generator Subsystem 87
- AMPLitude 89
- COUPling 89
- Audio Frequency Commands 91
- DISTortion 95
- Bit Error Test Subsystem 100
- LOOPback:LDELay 101
- LOOPback:LDELay:MODE 101
- Syntax BETest:TYPE<n>? 102
- Bit Error Test Commands 103
- (Measure Subsystem) 103
- Continued Over 104
- BESelect 106
- BERRor:COUNt 106
- BERRor:ICOunt 106
- BERRor:IRATio 107
- BERRor:RATio 107
- CRC:COUNt 108
- CRC:ICOunt 108
- CRC:IRATio 108
- CRC:RATio 109
- FERasure:COUNt 109
- FERasure:ICOunt 109
- FERasure:IRATio 110
- FERasure:RATio 110
- FLSelect 110
- IBTested 111
- Cell Configuration Subsystem 113
- Cell Configuration Subsystem 114
- ABCCh:BCC 119
- CCHannel 119
- CCHannel:SDCCH8:ARFCn 120
- CCHannel:SDCCH8:TSLot 120
- MA1:IOFFset 121
- MA2:IOFFset 122
- [:GSM900]:BA 122
- [:GSM900]:CA 123
- [:GSM900]:MA1 123
- [:GSM900]:MA1:IOFFset 123
- [:GSM900]:MA2 124
- [:GSM900]:MA2:IOFFset 124
- LAI:MCCode 124
- LAI:MNCode 125
- LAI:LACode 125
- SCELl:ARFCn 125
- SCELl:BCC 125
- SCELl:NCC 126
- Cell Control Subsystem 127
- AUDio:DAI:ATESt 134
- AUDio:DAI:NORMal 134
- AUDio:LOOPback 134
- AUDio:LOOPback:FAST 134
- AUDio:LOOPback:FE 134
- AUDio:LOOPback:OFF 135
- AUDio:LOOPback:NOFE 135
- AUDio:SPEech:CONFigure 135
- AUDio:SPEech:EDELay 136
- AUDio:SPEech:GAIN 136
- AUDio:SPEech:PRBS:PATTern 136
- CALL:CONNect 137
- CALL:COUNt:BSYNc 137
- CALL:COUNt:DERRor 137
- CALL:COUNt:PAGE 137
- CALL:COUNt:RACH 138
- CALL:COUNt:RESet 138
- CALL:END 138
- CALL:LIMit 138
- CALL:ORIGinate 139
- CALL:PAGing 139
- CALL:RECeive 139
- CALL:SIGNaling 140
- CALL:TCH:ARFCn 140
- CALL:TCH:TSLot 140
- CALL:STATus:CALLer 140
- CALL:STATus:CIPHering[:STATe] 141
- CALL:STATus:MM[:STATe] 141
- CALL:STATus:RR[:STATe] 142
- CALL:STATus:STATe 142
- CALL:STATus:TCH:ARFCn 142
- CALL:STATus:TCH:MALLocation 143
- CALL:STATus:TCH:MODE 143
- CALL:STATus:TCH:TSLot 143
- CALL:STATus:TCH:TYPE 143
- CALL:TCHControl 144
- CALL:TCHControl:EXECute 144
- MS:DRX[:STATe] 145
- MS:DTX[:STATe] 145
- MS:TADVance 145
- MS:TADVance:MODE 145
- MS:TLEVel 146
- TCH1 or TCH2:ARFCn 146
- TCH1 or TCH2:MALLocation 146
- TCH1 or TCH2:MODE 146
- TCH1 or TCH2:TSLot 147
- TCH1 or TCH2:TYPE 147
- Configure Subsystem 149
- Configure Subsystem 150
- BADDress 155
- COMPatible 156
- INTensity 156
- OFLevel:MODE 156
- OFLevel:AUXout 157
- OFLevel:RFINout 157
- OFLevel:AUXin 157
- OPERation:AUTO 158
- OPERation:HOLD 158
- PRINt:ADDRess 158
- PRINt:DESTination 159
- PRINt:FFENd 159
- PRINt:FFSTart 159
- PRINt:LINes 159
- PRINt:PRINter 160
- PRINt:TITle 160
- RFIMpedance 160
- ROSCillator:CALibrate 161
- ROSCillator[:FREQuency] 161
- ROSCillator:OFFset 161
- ROSCillator:TUNing 161
- SPORt:BAUD 162
- SPORt:DATA 162
- SPORt:IBECho 162
- SPORt:PARity 163
- SPORt:RPACe 163
- SPORt:SIN 163
- SPORt:STOP 164
- SPORt:XPACe 164
- CW Subsystem 165
- Syntax CW:PMZero 166
- Options Not Applicable 166
- FREQuency[:ABSolute] 169
- FREQuency:ERRor 169
- FREQuency:SELect 169
- Syntax MEASure:CW:POWer? 170
- DISPlay Subsystem 171
- [:SCReen] 173
- BETest:MNUMber:LEFT 173
- BETest:MNUMber:RIGHt 173
- CELL:SACCh:ACEL1 173
- CELL:TCH[:SELect] 174
- DSPanalyzer:AMPLitude:MASK 174
- DSPanalyzer:VIEW 174
- MSYNc:BURSt:NUMBer 175
- ORFSpectrum:VIEW 175
- PULSe:VIEW 176
- SANalyzer:CONTrol 176
- DSP Analyzer Subsystem 177
- AMPLitude:MARKer:POSition:MID 179
- AMPLitude:PMZero 179
- AMPLitude:TIME 180
- DBITs:TPOLarity 180
- PHASe:MARKer:POSition 180
- PHASe:MIDamble 180
- DSP Analyzer Commands 181
- [:AMPLitude]:AMPLitude 184
- [:AMPLitude]:MARKer:LEVEL:MID 185
- [:AMPLitude]:MARKer:TIME:FALL 186
- [:AMPLitude]:MARKer:TIME:MID 186
- [:AMPLitude]:MARKer:TIME:RISE 187
- [:AMPLitude]:MSUMmary 187
- [:AMPLitude]:NPFLatness 188
- [:AMPLitude]:PPFLatness 188
- [:AMPLitude]:PTCPower 188
- [:AMPLitude]:TRACe 189
- DBITs:TAGS 189
- FMERrors 190
- PHASe[:ERRor]:FREQuency 190
- PHASe[:ERRor]:PEAK 191
- PHASe[:ERRor]:RMS 191
- PHASe:MARKer:ERRor 192
- PHASe:MARKer:TIME 192
- PHASe:MBURst 192
- PHASe:MBURst:COUNt 193
- PHASe:MBURst:DONE 193
- PHASe:MBURst:ERRors 193
- PHASe:TRACe 193
- (no spaces) 197
- DATA <data entry> 198
- TIMEout:MS:XON 198
- TIMEout:MS:RESPonse 199
- Fast Bit Error Test 201
- RFGenerator:ATSLot 204
- BERRor:ICOUnt 207
- FTCPower[:POWer] 210
- Hop Control Subsystem 211
- ADDRess:NEXT 214
- ADDRess:RESet 214
- ADDRess:SOURce 214
- Options ‘ARM’ 218
- IEEE 488.2 Common Commands 219
- *CLS (Clear Status) 220
- *ESE (Event Status Enable) 221
- *ESR? (Event Status Register) 222
- *IDN? (Identification Number) 223
- *OPC (Operation Complete) 224
- Query Syntax *OPT? 225
- *RCL (Recall) 226
- *RST (Reset) 227
- *SAV (Save) 228
- *SRE (Service Request Enable) 229
- *STB? (Status Byte) 230
- *TST? (Test) 231
- *WAI (Wait) 232
- LOGGing Subsystem 233
- DATA:FLUSh 235
- DATA:CLEar 235
- Syntax LOGGing:STATe? 236
- Options ’LOG’ 236
- Measurement Sync Subsystem 237
- BURSt:LENGth 239
- BURSt:SPSPosition 239
- BURSt:TQUalifier 239
- BURSt:TYPE 240
- BURSt:UDSPattern 240
- SYNC:BSELect 240
- SYNC:MODE 241
- Mobile Station Commands 243
- MS:TERRor 245
- SACCh:ACEL1:ARFCn 245
- SACCh:ACEL1:BCC 245
- SACCh:ACEL1:NCC 245
- SACCh:ACEL1:RLEVel 246
- SACCh:FULL:RLEVel 246
- SACCh:FULL:RQUality 246
- SACCh:PARTial:RLEVel 246
- SACCh:PARTial:RQUality 246
- SACCh:RESet 247
- SACCh:TADVance 247
- SACCh:TLEVel 247
- MS Information Subsystem 249
- CIPHering:AMODe 251
- CIPHering:KC 251
- CIPHering:KI 252
- CIPHering:RAND 252
- CIPHering:SRES 252
- CIPHering[:STATe] 252
- MS:ATTach 253
- MS:CMARk:PCLass? 253
- MS:CMARk:REVision? 253
- MS:CMARk:BAND? 253
- MS:IMEI:REQuest 254
- MS:IMEI? 254
- MS:IMSI:SPAGing 254
- MS:IMSI? 254
- MS:LAI:LACode? 254
- MS:LAI:MCCode? 255
- MS:LAI:MNCode? 255
- MS:ONUMber? 255
- MS:PAGPer 255
- MS:SRES? 255
- [:PAGing]:IMSIdentity 256
- [:PAGing]:TMSI:REALlocation 256
- [:PAGing]:TMSI:STATe 256
- OSCilloscope Subsystem 257
- MARKer:NPEak 259
- MARKer:PPEak 259
- MARKer:POSition 259
- SCALe:TIME 260
- SCALe:VERTical:AM 260
- SCALe:VERTical:FM 260
- SCALe:VERTical:OFFSet 261
- SCALe:VERTical:VOLTs 261
- TRIGger:LEVel 261
- TRIGger:MODE 262
- TRIGger:PRETrigger 262
- TRIGger:RESet 262
- TRIGger:SENSe 263
- TRIGger:SOURce 263
- TRIGger:TYPE 263
- MARKer:LEVel:AM 267
- MARKer:LEVel:FM 267
- MARKer:LEVel:VOLTs 267
- MARKer:TIME 268
- Output RF Spectrum Subsystem 269
- FREQuency:OFFSet 271
- SACalibrate 272
- Output RF Spectrum Commands 273
- MARKer:LEVel 275
- [:POWer] 276
- PULSe On/Off Ratio Subsystem 279
- MARKer[:POSition]:FALL 281
- MARKer[:POSition]:RISE 281
- MARKer:OPOSition:FALL 281
- MARKer:OPOSition:RISE 282
- Pulse On/Off Ratio Commands 283
- MARKer:LEVel:FALL 285
- MARKer:LEVel:RISE 286
- MARKer:TIME:FALL 286
- MARKer:TIME:RISE 287
- OORatio:FALL 287
- OORatio:RISE 287
- Syntax MEASure:PULSe:SSTatus? 288
- TRACe:FALL 289
- TRACe:RISE 289
- RF Analyzer Subsystem 291
- AGC:CALibrate 294
- AGC:DVALue 294
- AGC:MODE 294
- AMPLitude1 294
- AMPLitude2 295
- [:AMPLitude]:ACCuracy 295
- [:AMPLitude]:CONTrol 295
- FREQuency 296
- FREQuency:GTIMe 296
- FREQuency:HMEas 296
- RF Generator Subsystem 299
- AMPLitude1:ATTenuation[:AUTO] 301
- AMPLitude2:ATTenuation[:AUTO] 301
- MODulation:DCAM 302
- MODulation:DCAM:DVALue 303
- MODulation:GMSK 303
- MODulation:PULSe 303
- MODulation:PULSe:MODE 304
- SMS Cell Broadcast Subsystem 305
- MESS1 or MESS2:CODE 308
- MESS1 or MESS2:UPDate 308
- MESS1 or MESS2:IDENtifier 309
- MESS1 or MESS2:LANGuage 309
- Spectrum Analyzer Subsystem 311
- ATTenuator 314
- ATTenuator:MODE 314
- ATTenuator2 314
- CFRequency 315
- MARKer:CFRequency 315
- MARKer:PEAK 315
- MARKer:RLEVel 316
- TRACe:MHOLd 317
- Spectrum Analyzer Commands 319
- MARKer:FREQuency 321
- Status Subsystem 323
- EMMI Status Register 328
- Event register bit def 328
- CONDition 329
- NTRanistion 329
- PTRanistion 330
- System Subsystem 331
- SYSTem[:ERRor] 332
- Tests Subsystem 333
- COMMent1 335
- COMMent2 335
- CONFigure? 335
- EXECution:DESTination 336
- EXECution:FAILure 336
- EXECution:HEADing1 337
- EXECution:HEADing2 337
- EXECution:RESults 338
- EXECution:RUN 339
- FREQuency? 339
- LIBRary? 340
- PARMameter? 340
- PROCedure:AUTOstart 340
- PROCedure:LOCation 341
- PROCedure:NAME 341
- PROCedure:PRINt:CONFigure 341
- PROCedure:PRINt:FREQuency 341
- PROCedure:PRINt:PARameter 342
- PROCedure:PRINt:SEQuence 342
- PROCedure:PRINt:SPEC 342
- PROCedure:RUN 342
- SEQNumber? 343
- Trigger Subsystem 345
- BETest:MODE 349
- DDEMod:ADJMode 349
- DDEMod:ASTate 349
- DDEMod:SOURce 350
- HTCH:ARFCn[:SPECific] 351
- HTCH:ARFCn:AUTO 351
- [:IMMediate] 351
- MODE[:DSP] 352
- MODE:RETRigger 352
- UMEMory:SOURce 353
- UMEMory:STATus 354
- Numeric Fields 357
- Commands 359
- Numeric (less MODE) 361
- REFerence:STATe? 372
- REFerence[:VALue]? 372
- Using Averaging 373
- Using Meters 377
- Fields Using Multi-Burst 381
Related products and manuals for Networking Agilent Technologies 8922M
(184 pages)© 2020, manymanuals.com. All rights reserved. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals