Agilent Technologies E1401-90493 User Manual Page 150
- Page / 642
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
150 Chapter 2
Performance Verification Tests
20. Overall Absolute Amplitude Accuracy: Agilent E4402B, E4403B, E4404B, E4405B, E4407B,
and E4408B
20. Overall Absolute Amplitude Accuracy:
Agilent E4402B, E4403B, E4404B, E4405B,
E4407B, and E4408B
This test measures the absolute amplitude of the analyzer at 50 MHz. A
synthesized signal generator and attenuators are used as the signal
source to the analyzer. A power meter is used to measure this signal
source with the attenuators set to 0 dB. The value measured is recorded
as the source amplitude. The attenuators are used to adjust the signal
levels applied to the analyzer from the initial signal amplitude (set with
the power meter) and –50 dBm. The amplitude measured by the
analyzer is compared to the actual signal level and the amplitude error
is calculated.
There are no related adjustment procedures for this performance test.
Equipment Required
Synthesized signal generator
10 dB step attenuator
1 dB step attenuator
Attenuator interconnection kit
Attenuator driver (if programmable step attenuators are used)
6 dB fixed attenuator (2 required)
Power meter
RF power sensor
Cable, Type-N, 62 cm (24 in.) (m) (2 required)
Cable, BNC
Adapter, Type-N (f) to Type-N (f)
Additional Equipment for Option BAB
Adapter, Type N (f) to APC 3.5 (f)
Procedure
Measuring 0 dBm Reference Level
1. Press
Preset on the analyzer. Press the Factory Preset softkey, if it is
displayed.
2. Connect a BNC cable from AMPTD REF OUT to the 50
Ω Input
connector using a Type N (m) to BNC (f) adapter.
3. Perform a complete self-alignment and set Auto Align Off. Press
System, Alignments, Align Now, All, and wait for the alignment routine
to finish. Then, press
Return, Auto Align, Off.
- Calibration Guide 1
- Contents 5
- 1Calibrating 9
- 10 Chapter 1 10
- Calibrating 10
- Calibration Cycle 11
- 12 Chapter 1 12
- Chapter 1 13 13
- Calibrating 13
- (This test has been deleted.) 13
- 14 Chapter 1 14
- Chapter 1 15 15
- 16 Chapter 1 16
- Chapter 1 17 17
- 18 Chapter 1 18
- Chapter 1 19 19
- 20 Chapter 1 20
- 22 Chapter 1 22
- Chapter 1 23 23
- Before You Start 24
- Test equipment you will need 25
- 8663A P,A 26
- >45 dB 30
- >42 dB 30
- Ω (2 required for Option 1DQ) 31
- Ω Minimum Loss 31
- ≥122 cm (48 in) 32
- ≥91 cm (36 in) 32
- 34 Chapter 2 34
- Chapter 2 35 35
- 36 Chapter 2 36
- Calibration 37
- Ω/1 MΩ until the LED is lit 43
- E4403B, and E4411B 48
- Accuracy 56
- 6. Frequency Span Accuracy: 59
- 7. Noise Sidebands 63
- −10 kHz: 65
- −10 kHz 65
- −20 kHz: 67
- −20 kHz 67
- −30 kHz: 67
- −30 kHz 68
- −100 kHz: 68
- −100 kHz 72
- −1 MHz: 72
- −5 MHz: 73
- −10 MHz: 73
- 9. System-Related Sidebands 75
- 10. Residual FM 78
- →, Mkr → CF 80
- ∆ Mkr1) amplitude, take its 82
- 11. Sweep Time Accuracy 83
- ∆ Mkr1) 85
- – 0 dB from R 92
- Bandwidths 93
- 89.3 mV== 94
- ATmeas–ATref+()10⁄ 96
- ∆Mkr Reading – Total 98
- Resolution Bandwidths 99
- Ω to 75 Ω minimum loss pad 100
- Procedure 101
- Ω input analyzers) should be 103
- Ω Input only) 103
- −57 dBm± 0.1 dB 104
- −8.2 dBmV ± 0.1 dB 104
- 17.On the analyzer, press 106
- Ω input of the analyzer 107
- −90 dBm (−41.25 107
- 110 Chapter 2 110
- Ω input and the dBmV col 111
- Ω input 111
- 112 Chapter 2 112
- Single on the analyzer 112
- Peak Search (or Search) 112
- Ω Input of the analyzer 117
- −90 dBm (with 117
- 30.23dB–= 119
- Uncertainty 125
- →, Mkr →CF 126
- →, Mkr →CF, Peak Search (or 126
- Ω to Type-N (m) 50 Ω 129
- Ω analyzers) or the 130
- Ω analyzers) 130
- Chapter 2 131 131
- Ω−27 dBm 132
- Ω−24 dBm 132
- −25 dBm (50Ω Input only) 133
- E4405B, E4407B, and E4408B 136
- −14 dBm ±0.1 dB 137
- − Channel B Power 138
- −14.07 dBm and Channel B 138
- −20.30 dB 138
- , Auto Align, All 142
- RefAtten 144
- 10 dB Actual 144
- 1 dB Actual 144
- Ω adapter 145
- ActualTotalAtten RefAtten 146
- Chapter 2 149 149
- Ω Input 150
- Equipment Required 157
- −5dBm ±0.2 dB 159
- ±0.05 dB 159
- − Lower Marker 159
- −7dBm ±0.2 dB 160
- Ω, BNC (m) 162
- ±0.1 dB 164
- Ω inputs 165
- ±0.1 dB 167
- ±0.1 dB for the current 167
- Ω inputs (Option 1DP) 168
- ≤100 kHz 169
- Ω load replaces the power 172
- ±0.1 dB for 100 kHz 177
- Setup Change Error FlatError 178
- FlatError 178
- 184 Chapter 2 184
- Chapter 2 185 185
- ↑ will allow you to step 201
- Chapter 2 205 205
- 206 Chapter 2 206
- Chapter 2 209 209
- Chapter 2 211 211
- Ω inputs) 213
- Ω to Type-N (f) 75 Ω 213
- ±0.2 dB 218
- Agilent E4402B 221
- 238 Chapter 2 238
- Chapter 2 241 241
- Agilent E4401B and E4411B 244
- −10 dBm 246
- Ω Input) 247
- E4407B, and E4408B 249
- −10 dBm ±0.1 dB 250
- −20 dBm ±0.1 dB 250
- ∆ Mkr1 or 253
- → CF, Delta 258
- ↑, ↑, ↑. The center 259
- ∆ Mkr1) amplitude 262
- ≥1 kHz, press: SPAN, 4 kHz 266
- ↓, ↓. The center frequency 266
- ±0.10 dB 269
- ≥1 kHz, press SPAN, 4 kHz 276
- Ω to Type-N (f), 75 Ω 290
- Ω directional 291
- Ω analyzer 291
- −24 dBm 293
- ∆ Mkr1) amplitude is the 293
- Table 2-79 298
- _____ dB 302
- Chapter 2 303 303
- Ω Inputs 304
- Ω input only) 307
- 1. Press 308
- Ω Input using a BNC cable 309
- Ω tracking generator, do the 312
- ° to 30° C range, but within 313
- ° to 30° C range 313
- → , Mkr→ CF 314
- ° to 30° C range, but 321
- →, Μκρ→ ΧΦ 322
- Ω tracking 326
- if test 328
- →, Mkr→ CF 329
- 39. Residual Responses 330
- ≥5 ms) to a fast sweep time 333
- E4411B (Option 1DN or 1DQ) 335
- Chapter 2 337 337
- Chapter 2 339 339
- (Option 1DN) 340
- −18 -2 2) 341
- −7 dB vernier setting is 342
- −0.15 = 0.08 − 0.23) 342
- (Option 1DN or 1DQ) 343
- Ω, 1 MHz to 1.5 GHz 344
- Ω power sensor 344
- ≥100 kHz 344
- Ω RF Out 346
- Ω tracking generators only 347
- at 100 kHz ___________ dB 348
- DVM Readout= Level Flatness– 348
- Chapter 2 349 349
- −0.53 dBm, the 354
- −1.23 dB 354
- −1.01 dB 354
- Ω to 75 Ω Minimum loss pad 356
- ⇑ ⇓ arrows to adjust the DAC 357
- −10 dBm. Press 357
- ⇑ (step-up key) to 358
- ⇑ (step up key) to 362
- Ω Option only) 366
- ±200 kHz 367
- ±750 kHz 367
- Response 369
- −10 dBm. Press STORE 371
- Chapter 2 375 375
- ∆t markers 379
- 4. Press 380
- −500 ns and −650 ns 381
- Ω Inputs only) 384
- (or Search) 386
- 9. Record the marker delta ( 386
- AYZ only) 387
- ∆ Mkr1) frequency 392
- 396 Chapter 2 396
- Chapter 2 397 397
- 398 Chapter 2 398
- Ω Input using 400
- Chapter 2 401 401
- BAH and B7E) 406
- °C temperature 409
- ≥–25 dBm 410
- 412 Chapter 2 412
- <−25 dBm 414
- ≤−20 dBm 415
- <–25 415
- ≤–20 dBm 415
- 25.Continue with Part 2 417
- Amplitude Accuracy = 421
- Measured Amplitude Amptd 421
- ActualTotalAtten– RefAtten 421
- +()– 40dB+ 421
- 422 Chapter 2 422
- ActualTotalAtten–RefAtten 425
- Ω Power Sensor 428
- ±293.3 µHz 429
- ±0.000072 ppm 429
- ±0.000070 ppm 429
- GHz signal 453
- Test Record 479
- Ω Input (No Option 1DP) 617
- 634 Chapter 3 634
- If You Have a Problem 635
- 636 Chapter 4 636
- Check the Basics 637
- Read the Warranty 638
- Service Options 638
- Chapter 4 639 639
- Service Tag 640
- Original Packaging 640
- Figure 4-1 641
- Other Packaging 642
Related products and manuals for Measuring, testing & control Agilent Technologies E1401-90493
(20 pages)© 2020, manymanuals.com. All rights reserved. | 0.301 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals