Agilent Technologies E1401-90493 User Manual Page 65
- Page / 642
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2 65
Performance Verification Tests
7. Noise Sidebands
Det/Demod, Detector, Sample
Sweep, Sweep Time, 5 sec
Single
Wait for the completion of a sweep, then press Peak Search (or
Search).
5. Press the following analyzer keys to measure the noise sideband
level at 10 kHz:
Marker, Delta
More
, Function, Marker Noise (or Noise)
AMPLITUDE, –10 dBm
FREQUENCY,
CF Step, 10 kHz
Center Freq,
↑
SPAN, Zero Span
Single
Record the marker amplitude noise reading in Table 2-10 as the
Upper Sideband Noise Level at 10 kHz.
6. Press the following analyzer keys to measure the noise sideband
level at
−10 kHz:
FREQUENCY, Center Freq, ↓, ↓
Single
Record the marker amplitude noise reading in Table 2-10 as the
Lower Sideband Noise Level at
−10 kHz.
7. Press
FREQUENCY, Center Freq, ↑
8. Continue with Part 3: Noise Sideband Suppression at 20 kHz.
Part 2: Noise Sideband Suppression at 10 kHz (measured in
100 Hz RBW)
1. Perform the following steps to set up the equipment:
Set the synthesized signal generator controls as follows:
FREQUENCY, 1000 MHz
AMPLITUDE
, 0dBm
AM
, OFF
FM
, OFF
2. Connect the equipment as shown in Figure 2-7.
3. Press
Preset on the analyzer. Press the Factory Preset softkey, if it is
displayed. Set the analyzer by pressing the following keys:
FREQUENCY, 1 GHz
SPAN
, 10 MHz
AMPLITUDE
, Attenuation 10 dB (Man)
- Calibration Guide 1
- Contents 5
- 1Calibrating 9
- 10 Chapter 1 10
- Calibrating 10
- Calibration Cycle 11
- 12 Chapter 1 12
- Chapter 1 13 13
- Calibrating 13
- (This test has been deleted.) 13
- 14 Chapter 1 14
- Chapter 1 15 15
- 16 Chapter 1 16
- Chapter 1 17 17
- 18 Chapter 1 18
- Chapter 1 19 19
- 20 Chapter 1 20
- 22 Chapter 1 22
- Chapter 1 23 23
- Before You Start 24
- Test equipment you will need 25
- 8663A P,A 26
- >45 dB 30
- >42 dB 30
- Ω (2 required for Option 1DQ) 31
- Ω Minimum Loss 31
- ≥122 cm (48 in) 32
- ≥91 cm (36 in) 32
- 34 Chapter 2 34
- Chapter 2 35 35
- 36 Chapter 2 36
- Calibration 37
- Ω/1 MΩ until the LED is lit 43
- E4403B, and E4411B 48
- Accuracy 56
- 6. Frequency Span Accuracy: 59
- 7. Noise Sidebands 63
- −10 kHz: 65
- −10 kHz 65
- −20 kHz: 67
- −20 kHz 67
- −30 kHz: 67
- −30 kHz 68
- −100 kHz: 68
- −100 kHz 72
- −1 MHz: 72
- −5 MHz: 73
- −10 MHz: 73
- 9. System-Related Sidebands 75
- 10. Residual FM 78
- →, Mkr → CF 80
- ∆ Mkr1) amplitude, take its 82
- 11. Sweep Time Accuracy 83
- ∆ Mkr1) 85
- – 0 dB from R 92
- Bandwidths 93
- 89.3 mV== 94
- ATmeas–ATref+()10⁄ 96
- ∆Mkr Reading – Total 98
- Resolution Bandwidths 99
- Ω to 75 Ω minimum loss pad 100
- Procedure 101
- Ω input analyzers) should be 103
- Ω Input only) 103
- −57 dBm± 0.1 dB 104
- −8.2 dBmV ± 0.1 dB 104
- 17.On the analyzer, press 106
- Ω input of the analyzer 107
- −90 dBm (−41.25 107
- 110 Chapter 2 110
- Ω input and the dBmV col 111
- Ω input 111
- 112 Chapter 2 112
- Single on the analyzer 112
- Peak Search (or Search) 112
- Ω Input of the analyzer 117
- −90 dBm (with 117
- 30.23dB–= 119
- Uncertainty 125
- →, Mkr →CF 126
- →, Mkr →CF, Peak Search (or 126
- Ω to Type-N (m) 50 Ω 129
- Ω analyzers) or the 130
- Ω analyzers) 130
- Chapter 2 131 131
- Ω−27 dBm 132
- Ω−24 dBm 132
- −25 dBm (50Ω Input only) 133
- E4405B, E4407B, and E4408B 136
- −14 dBm ±0.1 dB 137
- − Channel B Power 138
- −14.07 dBm and Channel B 138
- −20.30 dB 138
- , Auto Align, All 142
- RefAtten 144
- 10 dB Actual 144
- 1 dB Actual 144
- Ω adapter 145
- ActualTotalAtten RefAtten 146
- Chapter 2 149 149
- Ω Input 150
- Equipment Required 157
- −5dBm ±0.2 dB 159
- ±0.05 dB 159
- − Lower Marker 159
- −7dBm ±0.2 dB 160
- Ω, BNC (m) 162
- ±0.1 dB 164
- Ω inputs 165
- ±0.1 dB 167
- ±0.1 dB for the current 167
- Ω inputs (Option 1DP) 168
- ≤100 kHz 169
- Ω load replaces the power 172
- ±0.1 dB for 100 kHz 177
- Setup Change Error FlatError 178
- FlatError 178
- 184 Chapter 2 184
- Chapter 2 185 185
- ↑ will allow you to step 201
- Chapter 2 205 205
- 206 Chapter 2 206
- Chapter 2 209 209
- Chapter 2 211 211
- Ω inputs) 213
- Ω to Type-N (f) 75 Ω 213
- ±0.2 dB 218
- Agilent E4402B 221
- 238 Chapter 2 238
- Chapter 2 241 241
- Agilent E4401B and E4411B 244
- −10 dBm 246
- Ω Input) 247
- E4407B, and E4408B 249
- −10 dBm ±0.1 dB 250
- −20 dBm ±0.1 dB 250
- ∆ Mkr1 or 253
- → CF, Delta 258
- ↑, ↑, ↑. The center 259
- ∆ Mkr1) amplitude 262
- ≥1 kHz, press: SPAN, 4 kHz 266
- ↓, ↓. The center frequency 266
- ±0.10 dB 269
- ≥1 kHz, press SPAN, 4 kHz 276
- Ω to Type-N (f), 75 Ω 290
- Ω directional 291
- Ω analyzer 291
- −24 dBm 293
- ∆ Mkr1) amplitude is the 293
- Table 2-79 298
- _____ dB 302
- Chapter 2 303 303
- Ω Inputs 304
- Ω input only) 307
- 1. Press 308
- Ω Input using a BNC cable 309
- Ω tracking generator, do the 312
- ° to 30° C range, but within 313
- ° to 30° C range 313
- → , Mkr→ CF 314
- ° to 30° C range, but 321
- →, Μκρ→ ΧΦ 322
- Ω tracking 326
- if test 328
- →, Mkr→ CF 329
- 39. Residual Responses 330
- ≥5 ms) to a fast sweep time 333
- E4411B (Option 1DN or 1DQ) 335
- Chapter 2 337 337
- Chapter 2 339 339
- (Option 1DN) 340
- −18 -2 2) 341
- −7 dB vernier setting is 342
- −0.15 = 0.08 − 0.23) 342
- (Option 1DN or 1DQ) 343
- Ω, 1 MHz to 1.5 GHz 344
- Ω power sensor 344
- ≥100 kHz 344
- Ω RF Out 346
- Ω tracking generators only 347
- at 100 kHz ___________ dB 348
- DVM Readout= Level Flatness– 348
- Chapter 2 349 349
- −0.53 dBm, the 354
- −1.23 dB 354
- −1.01 dB 354
- Ω to 75 Ω Minimum loss pad 356
- ⇑ ⇓ arrows to adjust the DAC 357
- −10 dBm. Press 357
- ⇑ (step-up key) to 358
- ⇑ (step up key) to 362
- Ω Option only) 366
- ±200 kHz 367
- ±750 kHz 367
- Response 369
- −10 dBm. Press STORE 371
- Chapter 2 375 375
- ∆t markers 379
- 4. Press 380
- −500 ns and −650 ns 381
- Ω Inputs only) 384
- (or Search) 386
- 9. Record the marker delta ( 386
- AYZ only) 387
- ∆ Mkr1) frequency 392
- 396 Chapter 2 396
- Chapter 2 397 397
- 398 Chapter 2 398
- Ω Input using 400
- Chapter 2 401 401
- BAH and B7E) 406
- °C temperature 409
- ≥–25 dBm 410
- 412 Chapter 2 412
- <−25 dBm 414
- ≤−20 dBm 415
- <–25 415
- ≤–20 dBm 415
- 25.Continue with Part 2 417
- Amplitude Accuracy = 421
- Measured Amplitude Amptd 421
- ActualTotalAtten– RefAtten 421
- +()– 40dB+ 421
- 422 Chapter 2 422
- ActualTotalAtten–RefAtten 425
- Ω Power Sensor 428
- ±293.3 µHz 429
- ±0.000072 ppm 429
- ±0.000070 ppm 429
- GHz signal 453
- Test Record 479
- Ω Input (No Option 1DP) 617
- 634 Chapter 3 634
- If You Have a Problem 635
- 636 Chapter 4 636
- Check the Basics 637
- Read the Warranty 638
- Service Options 638
- Chapter 4 639 639
- Service Tag 640
- Original Packaging 640
- Figure 4-1 641
- Other Packaging 642
Related products and manuals for Measuring, testing & control Agilent Technologies E1401-90493
(20 pages)© 2020, manymanuals.com. All rights reserved. | 4.002 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals