Agilent Technologies 34401A Specifications Page 29
- Page / 482
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Power Meter Remote Operation
Configuring the Remote Interface
Agilent E4418B/E4419B Programming Guide 1-3
Configuring the Remote Interface
This section describes how to configure the GP-IB, RS232 and RS422
remote interfaces.
Interface Selection
You can choose to control the power meter remotely using either the
GP-IB, RS232 or RS422 standard interfaces.
For information on selecting the remote interface manually from the front
panel, refer to the Agilent Technologies E4418B/E4419B User’s Guides.
To select the interface remotely use the :
• SYSTem:RINTerface command
To query the current remote interface selection use the:
• SYSTem:RINTerface? command
GP-IB Address
Each device on the GP-IB (IEEE-488) interface must have a unique
address. You can set the power meter’s address to any value between 0
and 30. The address is set to 13 when the power meter is shipped from the
factory.
The address is stored in non-volatile memory, and does not change when
the power meter is switched off, or after a remote interface reset.
Your GP-IB bus controller has its own address. Avoid using the bus
controller’s address for any instrument on the interface bus.
Hewlett-Packard controllers generally use address 21.
For information on setting the GP-IB address manually from the front
panel, refer to the Agilent Technologies E4418B/E4419B User’s Guides.
To set the GP-IB address from the remote interface use the:
• SYSTem:COMMunicate:GPIB:ADDRess command.
To query the GP-IB address from the remote interface use the;
• SYSTem:COMMunicate:GPIB:ADDRess? query.
prog.book Page 3 Thursday, June 7, 2001 2:55 PM
- Programming Guide 1
- Legal Information 3
- Limitation of Warranty 4
- Exclusive Remedies 4
- Equipment Operation 5
- General Safety Considerations 6
- IEC 1010-1 Compliance 7
- Statement of Compliance 7
- User Environment 7
- Installation Instructions 7
- About this Guide 8
- List of Related Publications 10
- Table of Contents 11
- Table System... 1-45 12
- List of Figures 23
- List of Tables 25
- Introduction 28
- Interface Selection 29
- GP-IB Address 29
- RS232/RS422 Configuration 30
- Calibration 37
- Making Measurements 40
- Using MEASure? 41
- Using the CONFigure Command 46
- Using READ? 47
- Using INITiate and FETCh? 47
- Overview 56
- TABLE 20 57
- Making the Measurement 65
- TABLE 10 67
- Resolution 74
- Averaging 74
- Setting Offsets 77
- Setting Measurement Limits 79
- Setting Window Limits 81
- Checking for Limit Failures 81
- Measuring Pulsed Signals 84
- Triggering the Power Meter 87
- Idle State 89
- Initiate State 90
- Event Detection State 90
- Trigger Delay 91
- Trigger Mode 92
- Output Format 94
- Command Used 94
- 200 Readings/Sec 94
- Dual Channel Considerations 95
- How to Use Registers 100
- Power Meter Remote Operation 101
- Status Reporting 101
- Status Register 105
- Device Status Register 113
- Example Program 117
- Syntax Conventions 121
- SCPI Data Types 121
- Input Message Terminators 127
- Quick Reference 128
- MEASurement Commands 129
- CALCulate Subsystem 130
- CALibration Subsystem 131
- DISPlay Subsystem 131
- FORMat Subsystem 131
- MEMory Subsystem 132
- OUTPut Subsystem 132
- [SENSe] Subsystem 133
- STATus Subsystem 134
- SYSTem Subsystem 135
- TRIGger Subsystem 135
- UNIT Subsystem 136
- SERVice Subsystem 136
- SCPI Compliance Information 137
- SYSTem:RWLock 138
- TRANsmit:ECHO 138
- UNIT[1 138
- MEASurement Instructions 139
- CONFigure[1 145
- FETCh[1 159
- READ[1 173
- MEASure[1 187
- Figure 3-1: CALCulate Block 203
- CALCulate Block 203
- SENSe1 Block 203
- SENSe2 Block 203
- The CALCulate[1 204
- on the 205
- enabled 207
- disabled 207
- CALCulate[1 208
- CALCulate[1 213
- Error Message 218
- Conflict” occurs 218
- The CALCulate[1 221
- CALibration[1 231
- CALibration[1 234
- DISPlay[:WINDow[1 248
- Query Example 250
- MEMory:CATalog Node 267
- MEMory:CATalog[:ALL]? 268
- MEMory:CATalog:STATe? 270
- MEM :CAT :STAT ? 270
- MEMory:CATalog:TABLe? 271
- MEMory:CLEar Node 273
- MEMory:CLEar:TABLe 275
- MEM :CLE :TABL 275
- The MEMory:FREE Node 276
- MEMory:FREE[:ALL]? 277
- MEM :FREE :ALL 277
- MEMory:FREE:STATe? 278
- :FREE :STAT ? 278
- MEMory:FREE:TABLe? 279
- MEM :FREE :TABL 279
- MEMory:NSTates? 280
- MEM :NST 280
- The MEMory:STATe Node 281
- MEMory:STATe:CATalog? 282
- MEM :STAT :CAT 282
- MEMory:TABLe Node 285
- 80 Frequency 80 290
- OUTput Subsystem 295
- SENSe Subsystem 303
- Number of Averages 309
- • Auto-averaging is disabled 312
- CSET2) table 319
- B for channel B 329
- value is set but the 330
- [:INPut][:MAGNitude]? 333
- is not affected 333
- <numeric_value> 334
- or the values 336
- B for channel A 336
- “Hardware missing” occurs 359
- Device Status Register Sets 369
- Operation Register Sets 370
- STATus:PRESet 378
- Questionable Register Sets 379
- RO 396
- SYSTem:ERRor? 410
- SYStem:LOCal 412
- Command Setting Comments 413
- Setting Comments 414
- SYSTem:REMote 416
- SYST :REM 416
- SYSTem:VERSion? 419
- ABORt[1 423
- INITiate Node 424
- TRIGger Node 428
- IEEE488.2 Command Reference 453
- Universal Commands 455
- *SRE <NRf> 471
- TTL outputs 1-55 481
Related products and manuals for Multimeters Agilent Technologies 34401A
(14 pages)© 2020, manymanuals.com. All rights reserved. | 0.496 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals