Agilent Technologies N3280A User Manual download pdf (Page 107)

107

Line Voltage Selection

To change the line voltage selection:

1. Remove the line cord.

2. Check if the line voltage displayed in the window must be changed.

3. Open the door using a small flat-bladed screwdriver.

4. Rotate the cylinder so that the correct line voltage appears in the location under the window.

5. Pull the fuse drawer out and check if the fuse is correct for the line voltage that you have selected

(see Table 2-1). If the rating is incorrect, replace the fuse with the correct one.

120Vac120Vac

220Vac

100Vac

3 2

4 5

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 115 116

USER’S GUIDE 1
Warranty Information 2
Safety Summary 3
Declaration Page 5
Acoustic Noise Information 6
Printing History 6
Table of Contents 7
PROGRAMMING THE DC SOURCE 39 8
LANGUAGE DICTIONARY 53 9
SPECIFICATIONS 79 10
ERROR MESSAGES 103 11
LINE VOLTAGE SELECTION 107 11
INDEX 111 11
General Information 13
Options and Accessories 14
Description 14
Output Characteristics 15
Current Priority Operation 16
Measurement Characteristics 17
Start of a Measurement 18
Installation 19
Location 20
Power Connections 21
Outputs 1 - 4 22
Current Ratings 23
Coaxial Guard Connections 24
External Trigger Connections 25
Computer Connections 25
4 3 2 1 0 26
Address = 5 26
Turn-On Checkout 27
Checkout Procedure 28
In Case of Trouble 29
Introduction to Programming 31
Moving Among Subsystems 33
Including Common Commands 33
Using Queries 33
Types of SCPI Messages 34
SCPI Data Formats 35
SCPI Command Completion 36
Using Device Clear 37
Programming the DC Source 39
Overvoltage Protection 40
Output Current 40
Output Mode 40
Oscillation Protection 41
Output Trigger Model 41
Making Measurements 43
Power Line Cycles 44
Triggered Measurements 45
Measurement Trigger Model 46
Output Settling Delay 47
Operation Status Group 50
Questionable Status Group 51
Standard Event Status Group 51
Status Byte Register 51
Language Dictionary 53
6 – Language Dictionary 54
Language Dictionary - 6 55
Calibration Commands 57
CALibrate:DATA 58
CALibrate:DATE 58
CALibrate:LEVel 58
CALibrate:PASSword 58
CALibrate:SAVE 59
CALibrate:STATe 59
CALibrate:VOLTage 59
Measurement Commands 60
MEASure:ARRay:CURRent? 61
MEASure:ARRay:VOLTage? 61
MEASure:CURRent? 61
MEASure:VOLTage? 61
SENSe:CURRent:RANGe 61
SENSe:FUNCtion 62
SENSe:SWEep:NPLCycles 62
SENSe:SWEep:OFFSet:POINts 62
SENSe:SWEep:POINts 63
SENSe:SWEep:TINTerval 63
SENSe:WINDow 63
Output Commands 64
[SOURce:]CURRent[:IMMediate] 65
[SOURce:]CURRent:TRIGgered 65
[SOURce:]CURRent:LIMit:BWIDth 65
[SOURce:]CURRent:MODE 66
[SOURce:]CURRent:LIMit:MODE 66
[SOURce:]DELay 66
[SOURce:]DELay:MODE 66
[SOURce:]FUNCtion:MODE 67
[SOURce:]VOLTage:ALC:BWIDth 67
[SOURce:]VOLTage[:IMMediate] 67
[SOURce:]VOLTage:TRIGgered 67
[SOURce:]VOLTage:MODE 68
Status Commands 69
STATus:OPERation:NTR 70
STATus:OPERation:PTR 70
STATus:PRESet 70
STATus:QUEStionable[:EVENt]? 70
STATus:QUEStionable:ENABle 71
STATus:QUEStionable:NTR 71
STATus:QUEStionable:PTR 71
System Commands 72
Trigger Commands 73
TRIGger:ACQuire:SOURce 74
TRIGger[:TRANsient]:SOURce 74
TRIGger[:TRANsient] 74
Common Commands 75
6 – Language Dictionary 76
Language Dictionary - 6 77
Table 6-7. *RST Settings 77
Specifications 79
A - Specifications 80
Specifications - A 81
Introduction 83
Equipment Required 83
Measurement Techniques 84
Electronic Load 85
Programming 85
Test Setup 85
Voltage Priority Tests 86
Negative Current Limit (-CL) 87
Current Priority Tests 88
Load Effect Tests 89
Source Effect Tests 91
Ripple and Noise Tests 94
Transient Response Tests 95
Transient 96
Performance Test Record Form 98
Enable Calibration Mode 99
Calibration 101
Calibration Error Messages 102
Error Messages 103
C – Error Messages 104
Error Messages - C 105
Line Voltage Selection 107
Rear Panel Pinout Assignments 109
Mating Connector Part Numbers 109
Manual Updates 116

Comments to this Manuals

No comments

Agilent Technologies N3280A User Manual Page 107

Comments to this Manuals

Related products and manuals for Multimeters Agilent Technologies N3280A