Agilent Technologies N3280A User Manual Page 79
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
79
A
Specifications
Introduction
Table A-1 lists the specifications of the dc source. Unless otherwise noted, specifications are warranted
at 25°C ± 5°C after a 30-minute warm-up period. Sense terminals must be connected to their respective
output terminals.
Table A-1. Specifications
Parameter Voltage Priority Current Priority
Output Ratings
(refer to derating
characteristic)
Voltage:
Current:
-10.25V to +10.25V
- 0.5125A to +0.5125A
-8V to +8V (min. with full resistive load)
-11.25V to +11.25V (max. with no load)
- 0.5125 mA to +0.5125 mA
Programming Accuracy
Voltage
+ Current Limit:
- Current Limit:
Current:
0.1%±2mV
0.1%±50µA
0.1%±50µA
N/A
N/A
N/A
N/A
0.1%±1µA
Readback Accuracy
1
Voltage:
0.5A Curr. Range:
15mA Curr. Range:
0.5mA Curr. Range:
0.1%±2mV (5 points)
0.1%±200µA (5 points)
0.1%±5µA (5 points)
0.1%±200nA (1 PLC)
0.1%±2mV (5 points)
0.1%±200nA ( 1 PLC)
0.1%±200nA ( 1 PLC)
0.1%±200nA ( 1 PLC)
Ripple and Noise
(In the range of
20 Hz to 20 MHz )
Voltage (rms)
2
:
Voltage (p-p)
2
:
±Current Limit (rms)
3
:
Current (rms)
4
:
0.380mV
4mV
40µA
N/A
N/A
N/A
N/A
1.5µA
Load Effect
(Change from no load to full
load or full load to no load
by varying a resistive load)
Voltage:
+ Current Limit:
- Current Limit:
Current:
±400µV
±30µA
±30µA
N/A
N/A
N/A
N/A
±25nA
Source Effect
(change in output voltage or
current for any line change
within ratings)
Voltage:
+ Current Limit:
- Current Limit:
Current:
±200µV
±10µA
±10µA
N/A
N/A
N/A
N/A
±10nA
Output Transient
Response
Voltage (@ 10kHz)
5
:
(@ 20kHz):
(@ 30kHz):
Current
6
:
60µs
45µs
35µs
N/A
N/A
N/A
N/A
90µs
1
Voltage accuracy specification in voltage priority mode guaranteed between –10.25V to +10.25V. 0.5A current range accuracy specification
in voltage priority mode guaranteed between –0.5125A and +0.5125A. Readback for Voltage, 0.5A, and 15mA current ranges is based on
capturing 5 data points at intervals of 30.4µs and averaging the readings. Readback for 0.5mA current range is based on averaging the readings
over 1 power line cycle (60 Hz = 548 points @ 30.4µs). The default setting for all readback ranges is the average of 5 data points 30.4µs apart.
2
Program Vset to ±10V using a 20 ohm load resistor.
3
Program current to +500mA using a 20 ohm load resistor. Program Vset to ±10.25V.
4
Program current to ±0.5mA using a 16K ohm load resistor.
5
Measured with a 10uF output capacitor with 0.2 ohm ESR across the output with the current limit set to +0.5125A. The load current rise time
is approximately 10us for a current change of 0.25Ato 0.5A or 0.5A to 0.25A. Measure the output voltage recovery time to within 40mV of its
final value.
6
Measured following a voltage change of –1V to +1V or +1V to –1V with approximately 25us time constant with the current priority current
level set to 0uA. Measure the output current recovery time to within ±1mA of its final value.
- USER’S GUIDE 1
- Warranty Information 2
- Safety Summary 3
- Declaration Page 5
- Acoustic Noise Information 6
- Printing History 6
- Table of Contents 7
- PROGRAMMING THE DC SOURCE 39 8
- LANGUAGE DICTIONARY 53 9
- SPECIFICATIONS 79 10
- ERROR MESSAGES 103 11
- LINE VOLTAGE SELECTION 107 11
- INDEX 111 11
- General Information 13
- Options and Accessories 14
- Description 14
- Output Characteristics 15
- Current Priority Operation 16
- Measurement Characteristics 17
- Start of a Measurement 18
- Installation 19
- Location 20
- Power Connections 21
- Outputs 1 - 4 22
- Current Ratings 23
- Coaxial Guard Connections 24
- External Trigger Connections 25
- Computer Connections 25
- 4 3 2 1 0 26
- Address = 5 26
- Turn-On Checkout 27
- Checkout Procedure 28
- In Case of Trouble 29
- Introduction to Programming 31
- Moving Among Subsystems 33
- Including Common Commands 33
- Using Queries 33
- Types of SCPI Messages 34
- SCPI Data Formats 35
- SCPI Command Completion 36
- Using Device Clear 37
- Programming the DC Source 39
- Overvoltage Protection 40
- Output Current 40
- Output Mode 40
- Oscillation Protection 41
- Output Trigger Model 41
- Making Measurements 43
- Power Line Cycles 44
- Triggered Measurements 45
- Measurement Trigger Model 46
- Output Settling Delay 47
- Operation Status Group 50
- Questionable Status Group 51
- Standard Event Status Group 51
- Status Byte Register 51
- Language Dictionary 53
- 6 – Language Dictionary 54
- Language Dictionary - 6 55
- Calibration Commands 57
- CALibrate:DATA 58
- CALibrate:DATE 58
- CALibrate:LEVel 58
- CALibrate:PASSword 58
- CALibrate:SAVE 59
- CALibrate:STATe 59
- CALibrate:VOLTage 59
- Measurement Commands 60
- MEASure:ARRay:CURRent? 61
- MEASure:ARRay:VOLTage? 61
- MEASure:CURRent? 61
- MEASure:VOLTage? 61
- SENSe:CURRent:RANGe 61
- SENSe:FUNCtion 62
- SENSe:SWEep:NPLCycles 62
- SENSe:SWEep:OFFSet:POINts 62
- SENSe:SWEep:POINts 63
- SENSe:SWEep:TINTerval 63
- SENSe:WINDow 63
- Output Commands 64
- [SOURce:]CURRent[:IMMediate] 65
- [SOURce:]CURRent:TRIGgered 65
- [SOURce:]CURRent:LIMit:BWIDth 65
- [SOURce:]CURRent:MODE 66
- [SOURce:]CURRent:LIMit:MODE 66
- [SOURce:]DELay 66
- [SOURce:]DELay:MODE 66
- [SOURce:]FUNCtion:MODE 67
- [SOURce:]VOLTage:ALC:BWIDth 67
- [SOURce:]VOLTage[:IMMediate] 67
- [SOURce:]VOLTage:TRIGgered 67
- [SOURce:]VOLTage:MODE 68
- Status Commands 69
- STATus:OPERation:NTR 70
- STATus:OPERation:PTR 70
- STATus:PRESet 70
- STATus:QUEStionable[:EVENt]? 70
- STATus:QUEStionable:ENABle 71
- STATus:QUEStionable:NTR 71
- STATus:QUEStionable:PTR 71
- System Commands 72
- Trigger Commands 73
- TRIGger:ACQuire:SOURce 74
- TRIGger[:TRANsient]:SOURce 74
- TRIGger[:TRANsient] 74
- Common Commands 75
- 6 – Language Dictionary 76
- Language Dictionary - 6 77
- Table 6-7. *RST Settings 77
- Specifications 79
- A - Specifications 80
- Specifications - A 81
- Introduction 83
- Equipment Required 83
- Measurement Techniques 84
- Electronic Load 85
- Programming 85
- Test Setup 85
- Voltage Priority Tests 86
- Negative Current Limit (-CL) 87
- Current Priority Tests 88
- Load Effect Tests 89
- Source Effect Tests 91
- Ripple and Noise Tests 94
- Transient Response Tests 95
- Transient 96
- Performance Test Record Form 98
- Enable Calibration Mode 99
- Calibration 101
- Calibration Error Messages 102
- Error Messages 103
- C – Error Messages 104
- Error Messages - C 105
- Line Voltage Selection 107
- Rear Panel Pinout Assignments 109
- Mating Connector Part Numbers 109
- Manual Updates 116
Related products and manuals for Multimeters Agilent Technologies N3280A
(56 pages)© 2020, manymanuals.com. All rights reserved. | 1.206 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals