Agilent Technologies N3280A User Manual Page 61
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Language Dictionary - 6
61
MEASure:ARRay:CURRent?
MEASure:ARRay:VOLTage?
These queries initiate and trigger a measurement and return an array containing either the digitized output
current in amperes or output voltage in volts. The output voltage or current is digitized whenever a
measurement command is sent or an acquisition trigger occurs. The time interval is set by
SENSe:SWEep:TINTerval. The position of the trigger relative to the beginning of the data buffer is
determined by SENSe:SWEep:OFFSet. The number of points returned is set by SENSe:SWEep:POINts.
NOTE: You can specify an optional maximum value parameter. The dc source will select the
proper current range to measure the maximum current.
Query Syntax
MEASure:ARRay:CURRent[:DC]? [<maximum value>,] (@<channel list>)
MEASure:ARRay:VOLTage[:DC]? (@<channel list>)
Parameters
None
Examples
MEAS:ARR:CURR? 0.1,(@1) MEAS:ARR:VOLT? (@1)
Returned Parameters
<NR3>[,<NR3>]
Related Commands
SENS:SWE:TINT SENS:SWE:OFFS SENS:SWE:POIN
MEASure:CURRent?
MEASure:VOLTage?
These queries initiate and trigger a measurement and return either the output current in amperes or
output voltage in volts. The total measurement time is specified by SENSe:SWEep:NPLCycles.
NOTE: You can specify an optional maximum value parameter. This lets you use a different
current range for a single measurement without having to change current ranges.
Query Syntax
MEASure[:SCALar]:CURRent[:DC]? [<maximum value>,] (@<channel list>)
MEASure[:SCALar]:VOLTage[:DC]? (@<channel list>)
Parameters
None
Examples
MEAS:CURR? 0.1,(@1) MEAS:VOLT? (@1)
Returned Parameters
<NR3> [,<NR3>]
Related Commands
FETC:VOLT? FETC:CURR? SENS:SWE:NPLC
SENSe:CURRent:RANGe
This command selects one of the following dc current measurement ranges based on the value entered:
0.5 A
Enter values greater than 0.015A
15 mA
Enter values greater than 0.0005A up to 0.015A
0.5 mA
Enter values less than and up to 0.0005A
The programmed value must be the maximum current that you expect to measure. Crossover values are
0.5 mA and 15 mA respectively. When queried, the returned value is the maximum dc current that can be
measured on the range that is presently set.
Command Syntax
SENSe:CURRent[:DC]:RANGe[:UPPer] <Nrf>, (@<channel list>)
Parameters
The maximum current that you expect to measure (see table 6-3)
Unit
A (amperes)
*RST Value
0.5 A
Examples
SENS:CURR:RANG 0.4,(@1)
Query Syntax
SENSe:CURRent:RANGe? (@<channel list>)
Returned Parameters
<NR3>
- USER’S GUIDE 1
- Warranty Information 2
- Safety Summary 3
- Declaration Page 5
- Acoustic Noise Information 6
- Printing History 6
- Table of Contents 7
- PROGRAMMING THE DC SOURCE 39 8
- LANGUAGE DICTIONARY 53 9
- SPECIFICATIONS 79 10
- ERROR MESSAGES 103 11
- LINE VOLTAGE SELECTION 107 11
- INDEX 111 11
- General Information 13
- Options and Accessories 14
- Description 14
- Output Characteristics 15
- Current Priority Operation 16
- Measurement Characteristics 17
- Start of a Measurement 18
- Installation 19
- Location 20
- Power Connections 21
- Outputs 1 - 4 22
- Current Ratings 23
- Coaxial Guard Connections 24
- External Trigger Connections 25
- Computer Connections 25
- 4 3 2 1 0 26
- Address = 5 26
- Turn-On Checkout 27
- Checkout Procedure 28
- In Case of Trouble 29
- Introduction to Programming 31
- Moving Among Subsystems 33
- Including Common Commands 33
- Using Queries 33
- Types of SCPI Messages 34
- SCPI Data Formats 35
- SCPI Command Completion 36
- Using Device Clear 37
- Programming the DC Source 39
- Overvoltage Protection 40
- Output Current 40
- Output Mode 40
- Oscillation Protection 41
- Output Trigger Model 41
- Making Measurements 43
- Power Line Cycles 44
- Triggered Measurements 45
- Measurement Trigger Model 46
- Output Settling Delay 47
- Operation Status Group 50
- Questionable Status Group 51
- Standard Event Status Group 51
- Status Byte Register 51
- Language Dictionary 53
- 6 – Language Dictionary 54
- Language Dictionary - 6 55
- Calibration Commands 57
- CALibrate:DATA 58
- CALibrate:DATE 58
- CALibrate:LEVel 58
- CALibrate:PASSword 58
- CALibrate:SAVE 59
- CALibrate:STATe 59
- CALibrate:VOLTage 59
- Measurement Commands 60
- MEASure:ARRay:CURRent? 61
- MEASure:ARRay:VOLTage? 61
- MEASure:CURRent? 61
- MEASure:VOLTage? 61
- SENSe:CURRent:RANGe 61
- SENSe:FUNCtion 62
- SENSe:SWEep:NPLCycles 62
- SENSe:SWEep:OFFSet:POINts 62
- SENSe:SWEep:POINts 63
- SENSe:SWEep:TINTerval 63
- SENSe:WINDow 63
- Output Commands 64
- [SOURce:]CURRent[:IMMediate] 65
- [SOURce:]CURRent:TRIGgered 65
- [SOURce:]CURRent:LIMit:BWIDth 65
- [SOURce:]CURRent:MODE 66
- [SOURce:]CURRent:LIMit:MODE 66
- [SOURce:]DELay 66
- [SOURce:]DELay:MODE 66
- [SOURce:]FUNCtion:MODE 67
- [SOURce:]VOLTage:ALC:BWIDth 67
- [SOURce:]VOLTage[:IMMediate] 67
- [SOURce:]VOLTage:TRIGgered 67
- [SOURce:]VOLTage:MODE 68
- Status Commands 69
- STATus:OPERation:NTR 70
- STATus:OPERation:PTR 70
- STATus:PRESet 70
- STATus:QUEStionable[:EVENt]? 70
- STATus:QUEStionable:ENABle 71
- STATus:QUEStionable:NTR 71
- STATus:QUEStionable:PTR 71
- System Commands 72
- Trigger Commands 73
- TRIGger:ACQuire:SOURce 74
- TRIGger[:TRANsient]:SOURce 74
- TRIGger[:TRANsient] 74
- Common Commands 75
- 6 – Language Dictionary 76
- Language Dictionary - 6 77
- Table 6-7. *RST Settings 77
- Specifications 79
- A - Specifications 80
- Specifications - A 81
- Introduction 83
- Equipment Required 83
- Measurement Techniques 84
- Electronic Load 85
- Programming 85
- Test Setup 85
- Voltage Priority Tests 86
- Negative Current Limit (-CL) 87
- Current Priority Tests 88
- Load Effect Tests 89
- Source Effect Tests 91
- Ripple and Noise Tests 94
- Transient Response Tests 95
- Transient 96
- Performance Test Record Form 98
- Enable Calibration Mode 99
- Calibration 101
- Calibration Error Messages 102
- Error Messages 103
- C – Error Messages 104
- Error Messages - C 105
- Line Voltage Selection 107
- Rear Panel Pinout Assignments 109
- Mating Connector Part Numbers 109
- Manual Updates 116
Related products and manuals for Multimeters Agilent Technologies N3280A
(56 pages)© 2020, manymanuals.com. All rights reserved. | 0.732 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals