Agilent Technologies N3280A User Manual Page 59
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Language Dictionary - 6
59
CALibrate:SAVE
This command saves any new calibration constants after a calibration procedure has been completed in
nonvolatile memory. If CALibrate:STATe OFF is programmed without a CALibrate:SAVE, the previous
calibration constants are restored..
Command Syntax
CALibrate:SAVE
Parameters
None
Examples
CAL:SAVE
Related Commands
CAL:PASS CAL:STAT
CALibrate:STATe
This command enables and disables calibration mode. The calibration mode must be enabled before the
dc source will accept any other calibration commands.
The first parameter specifies the enabled or disabled state. The second parameter is the password. A
password is required if calibration mode is being enabled and the existing password is not 0. If the
password is not entered or is incorrect, an error is generated and the calibration mode remains disabled.
The query returns only the state, not the password.
NOTE: Whenever the calibration state is changed from enabled to disabled, any new calibration
constants are lost unless they have been stored with CALibrate:SAVE.
Command Syntax
CALibrate:STATe <bool>[,<NRf>]
Parameters
0 | OFF | 1 | ON [,<password>]
*RST Value
OFF
Examples
CAL:STAT 1,3280 CAL:STAT OFF
Query Syntax
CALibrate:STATe?
Returned Parameters
<NR1>
Related Commands
CAL:PASS CAL:SAVE *RST
CALibrate:VOLTage
This command initiates the calibration of the output voltage and the voltage measurement circuit.
Command Syntax
CALibrate:VOLTage (@<channel>)
Parameters
None
Examples
CAL:VOLT (@1)
- USER’S GUIDE 1
- Warranty Information 2
- Safety Summary 3
- Declaration Page 5
- Acoustic Noise Information 6
- Printing History 6
- Table of Contents 7
- PROGRAMMING THE DC SOURCE 39 8
- LANGUAGE DICTIONARY 53 9
- SPECIFICATIONS 79 10
- ERROR MESSAGES 103 11
- LINE VOLTAGE SELECTION 107 11
- INDEX 111 11
- General Information 13
- Options and Accessories 14
- Description 14
- Output Characteristics 15
- Current Priority Operation 16
- Measurement Characteristics 17
- Start of a Measurement 18
- Installation 19
- Location 20
- Power Connections 21
- Outputs 1 - 4 22
- Current Ratings 23
- Coaxial Guard Connections 24
- External Trigger Connections 25
- Computer Connections 25
- 4 3 2 1 0 26
- Address = 5 26
- Turn-On Checkout 27
- Checkout Procedure 28
- In Case of Trouble 29
- Introduction to Programming 31
- Moving Among Subsystems 33
- Including Common Commands 33
- Using Queries 33
- Types of SCPI Messages 34
- SCPI Data Formats 35
- SCPI Command Completion 36
- Using Device Clear 37
- Programming the DC Source 39
- Overvoltage Protection 40
- Output Current 40
- Output Mode 40
- Oscillation Protection 41
- Output Trigger Model 41
- Making Measurements 43
- Power Line Cycles 44
- Triggered Measurements 45
- Measurement Trigger Model 46
- Output Settling Delay 47
- Operation Status Group 50
- Questionable Status Group 51
- Standard Event Status Group 51
- Status Byte Register 51
- Language Dictionary 53
- 6 – Language Dictionary 54
- Language Dictionary - 6 55
- Calibration Commands 57
- CALibrate:DATA 58
- CALibrate:DATE 58
- CALibrate:LEVel 58
- CALibrate:PASSword 58
- CALibrate:SAVE 59
- CALibrate:STATe 59
- CALibrate:VOLTage 59
- Measurement Commands 60
- MEASure:ARRay:CURRent? 61
- MEASure:ARRay:VOLTage? 61
- MEASure:CURRent? 61
- MEASure:VOLTage? 61
- SENSe:CURRent:RANGe 61
- SENSe:FUNCtion 62
- SENSe:SWEep:NPLCycles 62
- SENSe:SWEep:OFFSet:POINts 62
- SENSe:SWEep:POINts 63
- SENSe:SWEep:TINTerval 63
- SENSe:WINDow 63
- Output Commands 64
- [SOURce:]CURRent[:IMMediate] 65
- [SOURce:]CURRent:TRIGgered 65
- [SOURce:]CURRent:LIMit:BWIDth 65
- [SOURce:]CURRent:MODE 66
- [SOURce:]CURRent:LIMit:MODE 66
- [SOURce:]DELay 66
- [SOURce:]DELay:MODE 66
- [SOURce:]FUNCtion:MODE 67
- [SOURce:]VOLTage:ALC:BWIDth 67
- [SOURce:]VOLTage[:IMMediate] 67
- [SOURce:]VOLTage:TRIGgered 67
- [SOURce:]VOLTage:MODE 68
- Status Commands 69
- STATus:OPERation:NTR 70
- STATus:OPERation:PTR 70
- STATus:PRESet 70
- STATus:QUEStionable[:EVENt]? 70
- STATus:QUEStionable:ENABle 71
- STATus:QUEStionable:NTR 71
- STATus:QUEStionable:PTR 71
- System Commands 72
- Trigger Commands 73
- TRIGger:ACQuire:SOURce 74
- TRIGger[:TRANsient]:SOURce 74
- TRIGger[:TRANsient] 74
- Common Commands 75
- 6 – Language Dictionary 76
- Language Dictionary - 6 77
- Table 6-7. *RST Settings 77
- Specifications 79
- A - Specifications 80
- Specifications - A 81
- Introduction 83
- Equipment Required 83
- Measurement Techniques 84
- Electronic Load 85
- Programming 85
- Test Setup 85
- Voltage Priority Tests 86
- Negative Current Limit (-CL) 87
- Current Priority Tests 88
- Load Effect Tests 89
- Source Effect Tests 91
- Ripple and Noise Tests 94
- Transient Response Tests 95
- Transient 96
- Performance Test Record Form 98
- Enable Calibration Mode 99
- Calibration 101
- Calibration Error Messages 102
- Error Messages 103
- C – Error Messages 104
- Error Messages - C 105
- Line Voltage Selection 107
- Rear Panel Pinout Assignments 109
- Mating Connector Part Numbers 109
- Manual Updates 116
Related products and manuals for Multimeters Agilent Technologies N3280A
(56 pages)© 2020, manymanuals.com. All rights reserved. | 1.241 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals