Agilent Technologies U2802A User Manual download pdf (Page 50)

U2701A/U2702A

Performance speciﬁcations

[1]

Vertical system: oscilloscope channels

Bandwidth (–3 dB) U2701A: DC to 100 MHz

U2702A: DC to 200 MHz

Scope channel triggering

Trigger sensitivity < 10 mV/div: greater of 1 div or 5mV; ≥10 mV/div: 0.6 div

Performance characteristics

[2]

Acquisition: oscilloscope channels

Real time sample rate

2 channels interleaved

Each channel

1 GSa/s

500 MSa/s

Standard memory depth

2 channels interleaved

Each channel

Normal Single-shot

32 Mpts 64 Mpts

16 Mpts 32 Mpts

Vertical resolution 8 bits

Peak detection Yes

Averaging Any number from 1 to 999

Filter Sin(x)/x interpolation for time base 1 ns to 100 ns

Sweep modes Auto, normal, single

Vertical system: oscilloscope channels

Scope channels U2701A/U2702A: Ch 1 and Ch 2 simultaneous acquisition

AC coupled U2701A: 3.5 Hz to 100 MHz

U2702A: 3.5 Hz to 200 MHz

Calculated rise time (= 0.35/bandwidth) U2701A: 3.5 ns

U2702A: 1.75 ns

Single-shot bandwidth U2701A: 100 MHz

U2702A: 200 MHz

Range 2 mV/div to 5 V/div (1 MΩ)

Maximum input

[3]

CAT I 30 Vrms, 42 Vpk

Offset range

±4 div

Example: ±8 mV on 2 mV/div; ±20 V on 5 V/div

Dynamic range ±4 div

Input impedance 1 MΩ: ≈ 16 pF

Coupling AC, DC, Ground

BW limit ≈ 25 MHz

Standard probes 10:1 Passive probe 150 MHz 1.2 m

10:1 Passive probe 300 MHz 1.2 m

ESD tolerance ±2 kV

Noise peak-to-peak 3 mVpp

DC vertical offset accuracy ≤ 200 mV/div: ±0.1 div ±2.0 mV ±0.5% offset value;

> 200 mV/div: ±0.1 div ±2.0 mV ±1.5% offset value

DC vertical gain accuracy ±4.0% of full scale

[1]

All speciﬁcations are warranted. speciﬁcations are valid after a 30-minute warm-up and within ±100 ºC of last calibration temperature.

[2]

All characteristics are typical performance values and are not warranted. Characteristics are valid after a 30-minute warm-up period and within

±10 ºC of last calibration temperature.

[3]

Under standalone use, you are only allowed to measure up to CAT I 30 Vrms. For high-voltage measurement up to CAT I 300 Vrms, you must install the

L-Mount kit on the U2701A/U2702A before plugging it into the product chassis. Ensure that the L-Mount kit installed on your modular oscilloscope is

screwed to the product chassis to ensure proper chassis grounding. Note that you are required to use the provided 10:1 probes (N2862A/N2863A)

for high-voltage measurements to avoid damaging your instrument.

1 ... 49 50 51 ... 74

Comments to this Manuals

No comments

Agilent Technologies U2802A User Manual Page 50

Comments to this Manuals

Related products and manuals for Measuring, testing & control Agilent Technologies U2802A