Agilent Technologies B1500A User's Guide Page 7
- Page / 202
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
• GROUND THE INSTRUMENT
This is Safety Class I instrument. To minimize shock hazard, the instrument
chassis and cabinet must be connected to an electrical ground. The power
terminal and the power cable must meet International Electrotechnical
Commission (IEC) safety standards.
• DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
Do not operate the instrument in the presence of flammable gases or fumes.
Operation of any electrical instrument in such an environment constitutes a
definite safety hazard.
• DO NOT REMOVE COVERS
No operator serviceable parts inside. Refer servicing to qualified personnel. To
prevent electrical shock do not remove covers.
• IN CASE OF DAMAGE
Instruments that appear damaged or defective should be made inoperative and
secured against unintended operation until they can be repaired by qualified
service personnel. Return the instrument to a Agilent Technologies sales or
service office for services and repair to ensure that safety features are maintained.
• USE ONLY THE SPECIFIC ACCESSORIES
Specific accessories satisfy the requirements for specific characteristics for using
the instrument. Use the specific accessories, cables, adapters, and so on for
safety reasons.
- Agilent B1500A 1
- Safety Summary 6
- Safety Symbols 8
- &$7 9
- v¨O½v¶´ 11
- Product Stewardship 16
- Precautionary Statement 17
- Working in Comfort 18
- In This Manual 20
- Contents 21
- 1 Getting Started 25
- + agb1500a 27
- + UsbDevice1 27
- To Turn B1500A On 28
- To Turn B1500A Off 28
- To Launch EasyEXPERT 30
- If Only One Workspace Exists 31
- To Create Workspace 32
- To Select Workspace 33
- To Use Tracer Test Mode 34
- To Use Application Test Mode 36
- Test Definitions 37
- To Use Classic Test Mode 38
- To Perform Measurement 40
- To Use Test Result Editor 41
- To Use Analysis Tools 42
- 2 Introduction 43
- Application Library 44
- Overview 45
- Agilent EasyEXPERT Software 48
- Front View 50
- Rear View 53
- GNDU - Ground Unit 59
- *1'8 59
- &RPPRQ 59
- About SMU 60
- HPSMU - High Power SMU 61
- MPSMU - Medium Power SMU 64
- To connect ASU 67
- Before using 1 pA range 67
- MCSMU - Medium Current SMU 68
- HRSMU - High Resolution SMU 70
- MFCMU - Multi Frequency CMU 74
- 300 k7 range 76
- 50 7 range 76
- HVSPGU - High Voltage SPGU 77
- 3 Installation 79
- Power Requirements 82
- Operating Environment 82
- Installation Requirements 83
- Power Cable 83
- Requirements 84
- Inspection and Installation 85
- To Perform Initial Setup 86
- To Change GPIB Address 88
- To Enable System Controller 89
- Installing Accessories 90
- To Set up 16442B (B1500A-A5F) 91
- To Connect Connector Plate 93
- To Connect ASU 95
- About ASU output cables 97
- To Connect SCUU/GSWU 99
- 6&88 100
- About SCUU output cables 101
- To Connect GNDU Adapter 103
- Selection switch SW2 and SW4 105
- Input Panel 106
- Output Panel 106
- Mounting Connectors 107
- 108
- ï ï0[ 108
- To Make an Interlock Circuit 109
- Connector side 109
- Interlock switch 109
- Wiring side 109
- Installation 111
- To Connect GNDU Output 112
- To Connect SMU Output 113
- To Minimize Leakage Current 114
- To Connect MCSMU Output 119
- To Connect MFCMU Output 120
- Stop key 121
- Using Test Fixture 122
- 6089 $0D[ 123
- 'UDLQ 123
- 6XEVWUDWH 123
- Using Connector Plate 124
- To Reduce Leakage Current 124
- '87 125
- To Measure Low Resistance 126
- Switching Matrix 128
- Required Conditions 129
- )25&(RU6(16($ 134
- )25&(RU6(16(% 134
- ,QVXODWRU 134
- 7ULD[LDO&DEOH 134
- Cleaning 136
- Self-test and Diagnostics 136
- Calibration 136
- Module Type and Locations 137
- To Interconnect SPGUs 138
- To Interconnect WGFMUs 139
- About Module Installation 140
- 4 Specifications 141
- Hardware 143
- Specification Conditions 143
- Supported Plug-in Modules 144
- Maximum Module Configuration 146
- Ground Unit (GNDU) 147
- MPSMU/HRSMU 148
- Specifications 149
- Connect ASU to dedicated SMU 151
- Connection path control 151
- SMU Common Specifications 157
- ± 1 mV (HPSMU) 161
- SCUU/GSWU 167
- : < 100 V at 300 sec 168
- Point Time Voltage 173
- Selector 174
- Selector Adapter 174
- WGFMU/RSU 175
- EasyEXPERT Software 182
- Operation mode 182
- Application library 182
- Oscilloscope view 183
- Measurement modes 184
- Sweep measurement 184
- Data display 186
- Automatic analysis function 187
- Arithmetic functions 187
- Workspace and data management 188
- External instrument control 188
- Furnished Software 189
- Desktop EasyEXPERT Software 190
- General Specifications 191
- 5 Accessories and Options 193
Related products and manuals for Measuring, testing & control Agilent Technologies B1500A
(364 pages)
(18 pages)© 2020, manymanuals.com. All rights reserved. | 2.384 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals