Agilent Technologies 34401A Service Manual Page 121
- Page / 163
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
To Replace the Current Input Fuses
The front and rear current input terminals are protected by two series
fuses. The first fuse is a 3 A, 250 Vac, fast-blow fuse and is located on
the rear panel. To replace this fuse, order Agilent part number
2110-0780.
A second fuse is located inside the multimeter to provide an additional
level of current protection. This fuse is a 7 A, 250 Vac, high-interrupt
rated fuse (Agilent part number 2110-0614). To replace this fuse, you
must remove the multimeter’s case by loosening three screws (see the
mechanical disassembly drawing on page 9-3).
To Connect the Pass/Fail Output Signals
The RS-232 connector on the multimeter’s rear panel is a 9-pin connector
(
DB-9, male connector). When the RS-232 interface is not selected
(
IEEE-488 interface is selected), the internal pass and fail TTL output
signals (limit testing) may be connected to the
RS-232 connector.
The pass and fail signals are low true and indicate the Math Pass/Fail
Limit Test result for the next reading to be output to the
GPIB interface.
The signals are active low for approximately 2 ms for each reading taken.
Pin Number
1
2
3
4
5
6
9
Input/Output
Output
Input
Output
Output
–
Input
Output
Description
* Limit Test Pass
Receive Data (RxD)
Transmit Data (TxD)
Data Terminal Ready (DTR)
Signal Ground (SG)
Data Set Ready (DSR)
* Limit Test Fail
* TTL output is available only after installing two jumpers inside the multimeter.
RS-232 Connector
6
Chapter 6 Service
To Replace the Current Input Fuses
115
- Agilent 34401A 1
- 6 ½ Digit Multimeter 1
- Safety Information 3
- Additional Notices 5
- DECLARATION OF CONFORMITY 6
- Multimeter 7
- The Front Panel at a Glance 8
- Display Annunciators 10
- The Rear Panel at a Glance 11
- In This Book 12
- Contents 13
- Specifications 17
- DC Characteristics 18
- Measuring Characteristics 19
- Chapter 1 Specifications 19
- AC Characteristics 20
- General Information 24
- HOLD Sensitivity: 24
- Product Dimensions 25
- ≤ 150 µV 26
- ≤ 15 µV 26
- ≤ 1.5 µV 26
- Measurement Error 27
- Sensitivity 28
- Resolution 29
- Accuracy 29
- Transfer Accuracy 30
- 24-Hour Accuracy 30
- 90-Day and 1-Year Accuracy 30
- Temperature Coefficients 30
- Quick Start 33
- ERROR annunciator turns on 35
- To Adjust the Carrying Handle 38
- To Measure Voltage 39
- To Measure Resistance 39
- To Measure Current 40
- To Test Continuity 41
- To Check Diodes 41
- To Select a Range 42
- To Set the Resolution 43
- To Make dB Measurements 46
- To Make dBm Measurements 47
- To Trigger the Multimeter 48
- Using an External Trigger 48
- -H.DDD,DDD EFFF 50
- -045.23 mVDC 50
- Agilent System II 51
- Menu Tutorial 53
- Front-Panel Menu Reference 55
- A Front-Panel Menu Tutorial 57
- Chapter 3 Menu Tutorial 58
- On/Off 59
- MEAS MENU is your first 61
- A: , B: , etc.) 61
- Shift < 61
- Auto/Man 63
- Calibration 65
- Procedures 65
- Calibration Procedures 66
- Agilent Calibration Services 67
- Calibration Interval 67
- Recommended Test Equipment 69
- Application 69
- Recommended Equipment 69
- Accuracy Requirements 69
- Test Considerations 70
- Self-Test 71
- ERROR annunciator 71
- Quick Performance Check 72
- Q in the 72
- Zero Offset Verification 73
- Input HI-LO and Sense HI-LO 73
- Gain Verification 75
- AC FILTER slow (MEAS MENU) 76
- Calibration Security Code 79
- Be careful 80
- Calibration Count 81
- Calibration Message 81
- Zero Adjustment 83
- Zero Adjustment Procedure 83
- Gain Adjustment 85
- Gain Adjustment Procedure 86
- – 100 kHz 86
- –10 Vdc Adjustment Procedure 88
- 500 Vdc Adjustment Procedure 89
- RAM U505 90
- MEAS MENU) 90
- ± 400 µA ac 90
- Input Frequency 91
- AC Filter Selected 91
- Settling Time 91
- Understanding Resolution 92
- -045.23 mVDC 93
- Error Messages 95
- out of range 96
- Calibration Error Messages 96
- Theory of 97
- Operation 97
- Theory of Operation 98
- Block Diagram 99
- Front/Rear Selection 100
- Function Switching 101
- DC Amplifier 102
- Input I and 103
- Ohms Current Source 104
- AC Circuit 105
- A-to-D Converter 107
- Floating Logic 109
- Earth-Referenced Logic 111
- Power Supplies 112
- Front Panel 113
- Service 115
- Operating Checklist 117
- Types of Service Available 118
- Repackaging for Shipment 119
- Surface Mount Repair 120
- RS-232 connector 121
- GPIB interface 121
- Installation Procedure 122
- Troubleshooting Hints 123
- Unit is inoperative 123
- Unit fails self-test 123
- Current input is inoperative 124
- Power supply problems 124
- Readings indicate OVERLOAD 124
- Power Supply Minimum Maximum 124
- Readings are inaccurate 125
- Readings show excessive noise 125
- Self-Test Procedures 126
- Power-On Self-Test 126
- Self-Test Descriptions 126
- Replaceable Parts 131
- To Order Replaceable Parts 132
- Backdating and Part Changes 132
- Chapter 7 Replaceable Parts 133
- Agilent 34401A Mainframe 140
- Manufacturer’s List 141
- Backdating 143
- Chapter 8 Backdating 145
- Agilent 34401A Multimeter 145
- Schematics 148
- Binder Edge (LH Page) 151
Related products and manuals for Multimeters Agilent Technologies 34401A
(8 pages)© 2020, manymanuals.com. All rights reserved. | 2.321 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals