Agilent Technologies 34401A Service Manual Page 92
- Page / 163
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Understanding Resolution
Resolution is expressed in terms of number of digits the multimeter can
measure or display. You can set the resolution to 4, 5, or 6 full digits,
plus a “
1
⁄
2
” digit which can only be a “0” or “1”. To increase measurement
accuracy and improve noise rejection, select 6
1
⁄
2
digits. To increase
measurement speed, select 4
1
⁄
2
digits.
Applies to all measurement functions. The resolution for the math
operations (null, min-max, dB, dBm, limit test) is the same as the
resolution for the measurement function in use.
The correspondence between the number of digits selected and the
resulting integration time (in power line cycles) is shown below.
The autozero mode is set indirectly when you set the resolution.
Resolution is local to the selected function. This means that you can
select the resolution for each function independently. The multimeter
remembers the resolution when you switch between functions.
Resolution Choices
Fast 4 Digit
* Slow 4 Digit
Fast 5 Digit
* Slow 5 Digit (default)
* Fast 6 Digit
Slow 6 Digit
Integration Time
0.02 PLC
1 PLC
0.2 PLC
10 PLC
10 PLC
100 PLC
* These settings configure the multimeter just as if you had pressed
the corresponding “DIGITS” keys from the front panel.
Chapter 4 Calibration Procedures
Understanding Resolution
86
- Agilent 34401A 1
- 6 ½ Digit Multimeter 1
- Safety Information 3
- Additional Notices 5
- DECLARATION OF CONFORMITY 6
- Multimeter 7
- The Front Panel at a Glance 8
- Display Annunciators 10
- The Rear Panel at a Glance 11
- In This Book 12
- Contents 13
- Specifications 17
- DC Characteristics 18
- Measuring Characteristics 19
- Chapter 1 Specifications 19
- AC Characteristics 20
- General Information 24
- HOLD Sensitivity: 24
- Product Dimensions 25
- ≤ 150 µV 26
- ≤ 15 µV 26
- ≤ 1.5 µV 26
- Measurement Error 27
- Sensitivity 28
- Resolution 29
- Accuracy 29
- Transfer Accuracy 30
- 24-Hour Accuracy 30
- 90-Day and 1-Year Accuracy 30
- Temperature Coefficients 30
- Quick Start 33
- ERROR annunciator turns on 35
- To Adjust the Carrying Handle 38
- To Measure Voltage 39
- To Measure Resistance 39
- To Measure Current 40
- To Test Continuity 41
- To Check Diodes 41
- To Select a Range 42
- To Set the Resolution 43
- To Make dB Measurements 46
- To Make dBm Measurements 47
- To Trigger the Multimeter 48
- Using an External Trigger 48
- -H.DDD,DDD EFFF 50
- -045.23 mVDC 50
- Agilent System II 51
- Menu Tutorial 53
- Front-Panel Menu Reference 55
- A Front-Panel Menu Tutorial 57
- Chapter 3 Menu Tutorial 58
- On/Off 59
- MEAS MENU is your first 61
- A: , B: , etc.) 61
- Shift < 61
- Auto/Man 63
- Calibration 65
- Procedures 65
- Calibration Procedures 66
- Agilent Calibration Services 67
- Calibration Interval 67
- Recommended Test Equipment 69
- Application 69
- Recommended Equipment 69
- Accuracy Requirements 69
- Test Considerations 70
- Self-Test 71
- ERROR annunciator 71
- Quick Performance Check 72
- Q in the 72
- Zero Offset Verification 73
- Input HI-LO and Sense HI-LO 73
- Gain Verification 75
- AC FILTER slow (MEAS MENU) 76
- Calibration Security Code 79
- Be careful 80
- Calibration Count 81
- Calibration Message 81
- Zero Adjustment 83
- Zero Adjustment Procedure 83
- Gain Adjustment 85
- Gain Adjustment Procedure 86
- – 100 kHz 86
- –10 Vdc Adjustment Procedure 88
- 500 Vdc Adjustment Procedure 89
- RAM U505 90
- MEAS MENU) 90
- ± 400 µA ac 90
- Input Frequency 91
- AC Filter Selected 91
- Settling Time 91
- Understanding Resolution 92
- -045.23 mVDC 93
- Error Messages 95
- out of range 96
- Calibration Error Messages 96
- Theory of 97
- Operation 97
- Theory of Operation 98
- Block Diagram 99
- Front/Rear Selection 100
- Function Switching 101
- DC Amplifier 102
- Input I and 103
- Ohms Current Source 104
- AC Circuit 105
- A-to-D Converter 107
- Floating Logic 109
- Earth-Referenced Logic 111
- Power Supplies 112
- Front Panel 113
- Service 115
- Operating Checklist 117
- Types of Service Available 118
- Repackaging for Shipment 119
- Surface Mount Repair 120
- RS-232 connector 121
- GPIB interface 121
- Installation Procedure 122
- Troubleshooting Hints 123
- Unit is inoperative 123
- Unit fails self-test 123
- Current input is inoperative 124
- Power supply problems 124
- Readings indicate OVERLOAD 124
- Power Supply Minimum Maximum 124
- Readings are inaccurate 125
- Readings show excessive noise 125
- Self-Test Procedures 126
- Power-On Self-Test 126
- Self-Test Descriptions 126
- Replaceable Parts 131
- To Order Replaceable Parts 132
- Backdating and Part Changes 132
- Chapter 7 Replaceable Parts 133
- Agilent 34401A Mainframe 140
- Manufacturer’s List 141
- Backdating 143
- Chapter 8 Backdating 145
- Agilent 34401A Multimeter 145
- Schematics 148
- Binder Edge (LH Page) 151
Related products and manuals for Multimeters Agilent Technologies 34401A
(8 pages)© 2020, manymanuals.com. All rights reserved. | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals