Agilent Technologies B1500A Service Manual Page 47
- Page / 110
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Module 5
Basic Measurement
5-27
Two SMUs in Parallel
SMU1
V=0 to 0.2
VAR1
VAR1’
V1
V2
Ground Unit
(GNDU) or
Chassis Gnd
SMU2
V=0 to 0.2
1 ohm
Use Ground Unit
or the chassis
ground as the
SMU return path.
Circuit Common
Shorting bar
NOTE
200 mA Output
Two SMUs can be operated in parallel.
The trick is to not use any SMU as COMMON.
HRSMU and MPSMU can only sink 100 mA.
Use GNDU (ground unit) or the chassis to sink the 200 mA of current. Chassis noise level will not
affect the measurement. There is a shorting bar in the back of the instrument which connects SMU
common to the chassis. The shorting bar must be connected as shown above. Use the connector on
the shorting bar to make an easy chassis connection to your circuit. The chassis connection is also
provided if you use a packaged part test fixture, such as the 16058A or 16442A/B.
Note
The only time you would ever want to remove the shorting bar, is the case of floating the instrument
circuit common when using other instruments. An example might be a connection to a RF Network
Analyzer. You may want to remove chassis ground loops by connecting the circuit common directly
to the NWA chassis.
Note
Never use the chassis ground for low current measurements. It is noisy. Use the GNDU or an SMU
set to 0 volts or COMMON mode.
Note
If the GNDU is used, connect the 16493L GNDU cable between the GNDU and the test fixture. Do
not connect the triaxial cable. The GNDU is rated for up to 4.2 A, while the maximum current rating
of the triaxial cable is 1 A.
- Agilent B1500A 1
- Semiconductor Device 1
- Analyzer 1
- Manual Part Number 2
- Warranty 2
- Technology Licenses 2
- Restricted Rights Legend 2
- In This Manual 4
- Class Exercises 6
- .xtr files 7
- Demo.xpg file 7
- .xtd files 7
- 1 ohm Resistor 10
- 1.1 kohm Resistor 10
- 511 kohm Resistor 10
- 0.1 uF Capacitor 10
- Module 1. Introduction 13
- Module 2. Getting Started 13
- Module 5. Basic Measurement 15
- Contents 20
- Contents-8 20
- 5 Basic Measurement 21
- In This Module 22
- SMU Block Diagram 23
- Basic Sweep Measurement 24
- Sweep Measurement Modes 25
- Combining VAR1, VAR1’, VAR2 25
- Why Four SMUs? 26
- Class Exercise 27
- SMU Triax Connection 28
- Wrong Triaxial Hookup 29
- Jumper Leads – MOS transistor 30
- To Import Demo Data 31
- To Get Setup Data 32
- Classic Test – Channel Setup 33
- Do not abort on 34
- Classic Test – Display Setup 35
- To Start Measurement 36
- Data Display Window – Graph 37
- Data Display Window - List 38
- Paste to Notepad 39
- To Copy List Data 39
- Application Test 40
- Module 5 41
- Basic Measurement 41
- SMUs May Be Connected 42
- 200 V Resistor Sweep 43
- 200 V BVceo 43
- Two SMUs in Series 44
- Voltage across resistor 44
- VR = V1-V2 44
- VAR1' Ratio = -1 45
- Measurement and Display Pages 45
- Graphics Page 0 to 200 V 46
- 200 mA Output 47
- Two SMUs in Parallel 48
- Current in resistor 48
- Itotal = I1+I2 48
- VAR1' Ratio = 1 49
- Resistor 50
- Graphics Page 0 to 200 mA 50
- Cabling and Fixturing Issues 51
- Simplified Diagram 52
- Kelvin Triaxial Cable 56
- Why Kelvin Measurements? 57
- Cable Connections 59
- Class Example - Jumper Leads 60
- 2. Click Recall button 61
- To Get REKELV Test Setup: 61
- Single Kelvin Measurement 62
- Non-Kelvin Measurement 63
- To Kelvin Probe 64
- To Guarded Chuck 64
- Connector Plate 65
- Guarded to within 2mm of tip 67
- Single Triax Kelvin Triax 67
- Triaxial Probes 67
- Simplifying RF Connections 68
- Interlock Connection 69
- 16493J-001 1.5 m cable 70
- 16493J-002 3.0 m cable 70
- 16442A/B Fixture 70
- 16058A Fixture Compatibility 71
- 6 Low Current Measurement 73
- Low Current Measurement 75
- What is possible? 75
- Challenges 76
- Clean Probing Environment 77
- What is Required? 77
- Where to Start? 78
- Low Current 79
- Calibration & Zero Cancel 79
- Calibration 80
- Measurements Near Zero fA 81
- ZERO CHECK - No cable 82
- Using Default SMU Setup 82
- Delete SMU1 and SMU2 83
- Change Mode to V and 83
- Function to VAR1 83
- ZERO CHECK 83
- Channel Setup 83
- Do not change this screen 84
- Display Setup 86
- Bumping cable 88
- Bending Cable 88
- Effect of cable movement 88
- Appendix: Using ASU 89
- Configuration 90
- HRSMU+ASU 91
- Low Current Subthreshold 92
- SD214DE MOS Subthreshold 94
- Trade Off Speed vs Accuracy 95
- What is measured? 96
- Low Current Gummel Plot 97
- Module 6 98
- Small step size 99
- Negative sweep values 99
- Range and Integration Time 100
- Maximum resolution 100
- Gummel Plot 100
- LOW CURRENT MEASUREMENT 101
- Gummel Plot With 102
- ULTRA LOW CURRENT 103
- Subthreshold Curve 103
- Small STEP: 100 mV 104
- Large HOLD TIME: 3 sec 104
- Measurement Setup 104
- Set long integration time 106
- Leakage to fA levels 107
- Chuck must be guarded 107
- Fowler-Nordheim (FN) Plot 108
- Negative sweep 109
- Accumulation mode 109
- Wait for 5 V initial step 109
- FOWLER-NORDHEIM PLOT 109
- Measurement Page 109
- Low Current Gate Oxide Meas 110
- Using Guarded Chuck 110
Related products and manuals for Measuring, testing & control Agilent Technologies B1500A
(628 pages)© 2020, manymanuals.com. All rights reserved. | 1.466 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals