Agilent Technologies E1418A User Manual Page 63
- Page / 190
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Implied
Commands
Implied commands appear in square brackets ([ ]) in the command syntax. (Note
that the brackets are not part of the command and are not sent to the instrument.)
Suppose you send a second level command but do not send the preceding implied
command. In this case, the instrument assumes you intend to use the implied
command and it responds as if you had sent it. Examine this excerpt from the
STATus subsystem shown below:
STATus:
OPERation
[:EVENt]?
The third level command, EVENt, is implied. To read the value of the Event
Register, you can use either:
STATus:OPERation?
or
STATus:OPERation:EVENt?
Parameters
Parameters are enclosed in greater than/less than symbols (< >) in the command
syntax. When more than one parameter is allowed, the parameters are separated by
a vertical line ( | ).
Parameter Types. The following table contains explanations and examples of
parameter types you might see later in this chapter. Parameters must always be
separated from the keywords by a space.
Parameter Type Explanations and Examples
Numeric Accepts all commonly used decimal representations of
numbers including optional signs, decimal points, and
scientific notation.
123, 123E2, -123, -1.23E2, .123, 1.23E-2, 1.23000E-01.
Special cases include MIN, MAX, and DEF.
Boolean Represents a single binary condition that is either
true or false.
ON, OFF, 1, 0.
Discrete Selects from a finite number of values. These parameters
use mnemonics to represent each valid setting.
An example is the SOURce
n:FUNCtion:MODE <mode>
command where the <
mode> parameter can be either
CURRent or VOLTage.
Optional Parameters. Parameters shown within square brackets ([ ]) are optional
parameters. (Note that the brackets are not part of the command and are not sent to
the instrument.) If you do not specify a value for an optional parameter, the
instrument chooses a default value.
Chapter 3 Agilent E1418A SCPI Command Reference 61
- *E1418-90002* 1
- Contents 3
- WARNINGS 10
- Printing History 10
- Safety Symbols 10
- DECLARATION OF CONFORMITY 11
- Module Setup and Installation 15
- Figure 1-1 shows the module 16
- Description 17
- Description Use 17
- – Ribbon Cable (Option A3H) 17
- Functional Description 18
- – Terminal Module 19
- Front Panel Connectors 20
- Module Installation 22
- Terminal Modules 24
- Wiring the Terminal Module 25
- Attaching the Terminal Module 27
- Removing the Terminal Module 28
- Terminal Module Options 29
- Crimp-and-Insert 30
- Terminal Module 30
- Accessories 30
- Extra Crimp-and-Insert 31
- Connectors 31
- Terminal Module Connectors 32
- Options A3E and A3H 34
- Terminals 34
- Terminal Module Connections 35
- Combining 36
- Channels 36
- Connecting an 37
- External Trigger 37
- Using the CAL 38
- Output Terminals 38
- Initial Operation 39
- Identification 40
- Programming Examples 41
- APPLy Output 47
- Error Checking 49
- SOURce Output 52
- Setting the Output Mode 54
- Controlling the Output Relay 55
- Triggering 56
- Using *OPC? 58
- Combining Output Channels 59
- Chapter 3 61
- Using This Chapter 61
- Command Types 61
- SCPI Command Format 62
- Commands 63
- Parameters 63
- SCPI Command Reference 64
- Subsystem Syntax ABORt 65
- APPLyn:CURRent 66
- APPLyn:VOLTage 67
- CALibration 68
- CALibration:CONDition? 69
- CALibration:RESet 70
- CALibration:STORe 71
- CALibration:TEST? 71
- CALibration:VALue:RESistance 72
- CALibrationn:VALue:CURRent? 75
- CALibrationn:VALue:VOLTage? 76
- DIAGnostic 78
- DIAGnostic:CONFigure? 79
- DIAGnostic:OUTPut:ALL[:STATe] 80
- DIAGnostic:TRIGgered? 81
- INITiate 82
- OUTPut:TTLTrgn[:STATe] 83
- OUTPut:TTLTrgn[:STATe]? 84
- OUTPutn[:STATe] 84
- OUTPutn[:STATe]? 85
- Subsystem Syntax SOURcen 86
- SOURcen:FUNCtion:MODE 91
- SOURcen:FUNCtion:MODE? 92
- Subsystem Syntax STATus 97
- STATus:OPERation:CONDition? 98
- STATus:OPERation:ENABle 98
- STATus:OPERation:ENABle? 99
- STATus:OPERation[:EVENt]? 99
- STATus:PRESet 99
- STATus:QUEStionable:ENABle 100
- STATus:QUEStionable:ENABle? 101
- STATus:QUEStionable[:EVENt]? 101
- SYSTem:ERRor? 102
- SYSTem:VERSion? 102
- TEST:NUMBer? 103
- TEST:TST[:RESults]? 104
- Parameters None 105
- TRIGger[:IMMediate] 106
- TRIGger:SOURce 107
- TRIGger:SOURce? 107
- Command Description 111
- Agilent E1418A Specifications 113
- Appendix B 115
- Addressing the Registers 116
- Reset and Registers 121
- Register Maps 122
- A24 REGISTERS 123
- Registers 124
- Cal Storage Registers 125
- Register Descriptions 128
- Device Type 129
- Register 129
- VXI Status/Control 129
- Base + 06 130
- READ A24 Offset 0000000000 130
- WRITE A24 Offset 0000000000 130
- Calibration Control 131
- Card Configuration 132
- Software Trigger 133
- Trigger Control 133
- Using the Trigger 134
- Control Register 134
- Interrupt Status 135
- Isolation Status 135
- Channel Program 136
- Jumper Register 136
- Channel Trigger 137
- Channel Mode 138
- Channel Relay 138
- Card Control 139
- Main_DAC 140
- Immediate 140
- Triggered Registers 140
- Offset_DAC 141
- Gain_DAC 141
- Undefined 142
- Channel Voltage 142
- Offset Calibration 142
- Gain Calibration 143
- Channel Current 144
- Calibration 146
- Resistor Value 146
- Voltage Calibration 146
- Status Register 146
- Current Calibration 147
- Calibration Card 149
- Configuration 149
- Checksum Register 149
- Register Example 150
- Agilent E1418A Error Messages 153
- Error Messages 154
- Appendix D 157
- Using This Appendix 157
- Equipment Required 158
- Making Connections 158
- Adjustment Procedure 159
- CALn:VAL:CURR? 164
- Storing the 165
- Adjustments 165
- Return the 165
- Module to Use 165
- Configuration and Disassembly 169
- Changing 170
- – Static Safe Workstation 171
- – Static Wrist Strap 171
- Installing 174
- Isolated/Non-Isolated 174
- Plug-on Modules 174
- Troubleshooting 176
- To Exchange an 177
- Assembly 177
- Agilent E1418A User’s Manual 179
- C (continued) 181
- O (continued) 185
- P (continued) 186
- R (continued) 187
- S (continued) 188
- T (continued) 189
- _DAC registers, 139 190
Related products and manuals for Video converters Agilent Technologies E1418A
(14 pages)© 2020, manymanuals.com. All rights reserved. | 0.178 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals