Agilent Technologies B1500A User's Guide Page 178
- Page / 204
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4- 38 Keysight B1500A User’s Guide, Edition 14
Specifications
Hardware
Table 4-18 Voltage force accuracy, resolution, and timing
V force (Fast IV mode) -5 V to +5 V, -10 V to 0 V, 0 V to +10 V
V force (PG mode) -5 V to +5 V, open load
-2.5 V to +2.5 V, 50 load
Accuracy
± 0.1 % of setting ± 0.1 % of range
a
a. Independent of the range or the mode. DC constant voltage output. Load
impedance must be 1 M (1 A range) or 200 k (all other current
ranges) for Fast IV mode, or 1 M for PG mode.
Resolution
b
b. Can vary at most 5 % based on the result of calibration
96 V (-3 V to +3 V)
160 V (all ranges except for -3 V to +3 V)
Overshoot/undershoot
± (5 % + 20 mV)
c
c. PG mode, 50 load, T
rise
and T
fall
>16 ns with the 1.5 m cable, >32 ns
with 3 m cable, or >56 ns with 5 m cable
Noise
Maximum 0.1 mV
rms
d
d. Theoretical value for the observed time 100 ns to 1 ms, supplemental
characteristics
Rise time T
rise
(10 to 90 %)/
Fall time T
fall
(90 to 10 %)
Accuracy: -5 % to +(5 % + 10 ns) of setting
e
e. PG mode, 50 load, T
rise
and T
fall
24 ns
Minimum: 24 ns, PG mode and 50 load
Pulse period
Timing accuracy: ± 1 % of setting
f
f. PG mode, 50 load, pulse period 100 ns
Minimum: 100 ns, PG mode and 50 load
Pulse width
Accuracy: ± (3 % + 2 ns)
g
g. PG mode, 50 load, pulse width 50 ns
Minimum: 50 ns, PG mode and 50 load
- Keysight Technologies B1500A 1
- Semiconductor Device Analyzer 1
- Safety Summary 6
- Safety Symbols 8
- Circuit Common 11
- Product Stewardship 16
- Precautionary Statement 17
- Working in Comfort 18
- In This Manual 20
- Contents 21
- 1 Getting Started 25
- + agb1500a 27
- + UsbDevice1 27
- To Turn B1500A On 28
- To Turn B1500A Off 28
- To Launch EasyEXPERT 30
- If Only One Workspace Exists 31
- To Create Workspace 32
- To Select Workspace 33
- To Use Tracer Test Mode 34
- To Use Application Test Mode 36
- Test Definitions 37
- To Use Classic Test Mode 38
- To Perform Measurement 40
- To Use Test Result Editor 41
- To Use Analysis Tools 42
- 2Introduction 43
- Application Library 44
- Overview 45
- Keysight EasyEXPERT Software 48
- Front View 50
- Rear View 53
- Measurement Modules 59
- About SMU 60
- HPSMU - High Power SMU 61
- MPSMU - Medium Power SMU 64
- To connect ASU 67
- Before using 1 pA range 67
- MCSMU - Medium Current SMU 68
- HRSMU - High Resolution SMU 70
- MFCMU - Multi Frequency CMU 74
- 300 k7 range 76
- 50 7 range 76
- HVSPGU - High Voltage SPGU 77
- 3 Installation 79
- Requirements 82
- Installation Requirements 83
- Power Cable 83
- Inspection and Installation 85
- To Perform Initial Setup 86
- To Change GPIB Address 88
- To Enable System Controller 89
- Installing Accessories 90
- To Set up 16442B (B1500A-A5F) 91
- To Connect Connector Plate 93
- To Connect ASU 95
- About ASU output cables 97
- To Connect SCUU/GSWU 99
- About SCUU output cables 101
- Connector handle 103
- Banana jack 103
- Selection switch SW2 and SW4 105
- Input Panel 106
- Output Panel 106
- Mounting Connectors 107
- 2 − 11.3 3.2 2 − M3 x 0.5 108
- 14 11 11 14 108
- Connector side 109
- Interlock switch 109
- Wiring side 109
- Installation 111
- To Connect GNDU Output 112
- To Connect SMU Output 113
- To Minimize Leakage Current 114
- To Connect MCSMU Output 119
- To Connect MFCMU Output 120
- Stop key 121
- Using Test Fixture 122
- SMU(±200V= 1A Max) 123
- Substrate 123
- To Reduce Leakage Current 124
- To Measure Low Resistance 126
- Switching Matrix 128
- Required Conditions 129
- FORCE or SENSE (A) 134
- FORCE or SENSE (B) 134
- Insulator 134
- Triaxial Cable 134
- Maintenance 136
- About Plug-in Modules 137
- To Interconnect SPGUs 138
- To Interconnect WGFMUs 139
- About Module Installation 140
- 4 Specifications 141
- Specification Conditions 143
- Supported Plug-in Modules 144
- Maximum Module Configuration 146
- Ground Unit (GNDU) 147
- MPSMU/HRSMU 148
- Specifications 149
- Hardware 149
- Connect ASU to dedicated SMU 151
- Connection path control 151
- SMU Common Specifications 157
- ± 1 mV (HPSMU) 161
- SCUU/GSWU 167
- V at 300 sec 168
- Point Time Voltage 173
- Selector 174
- Selector Adapter 174
- WGFMU/RSU 175
- Operation mode 182
- Application library 182
- Oscilloscope view 183
- Measurement modes 184
- Sweep measurement 184
- Data display 186
- Automatic analysis function 187
- Arithmetic functions 187
- Workspace and data management 188
- External instrument control 188
- Furnished Software 189
- Desktop EasyEXPERT Software 190
- General Specifications 191
- 5 Accessories and Options 193
- *B1500-90000* 204
Related products and manuals for Measuring, testing & control Agilent Technologies B1500A
(36 pages)© 2020, manymanuals.com. All rights reserved. | 0.306 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals