Agilent Technologies 16048A Specifications Page 72
- Page / 104
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
16339A Component Test Fixture
Terminal Connector:
* Interlock Connector enables and disables
the application of source voltage from the
measurement instrument.
DUT Connection: 2-Terminal (with triaxial cable)
Dimensions (approx.): 200(W) x 140(H) x 230 (D) [mm]
Cable Length (approx.): 0.8 m
Weight (approx.): 2200 g
68
DC (High resistance) SMD & Lead Components
Description: The 16339A is designed to operate specifi-
cally with 4339B. It is provided with three component
modules, which are used to hold SMD, lead and various
type of devices. Electrical noise effects are reduced by the
employment of a shielded case. A built-in interlocking cir-
cuit enables safe high-voltage measurements.
Applicable Instruments: 4339B
Frequency: DC
Maximum Voltage: 1000 V
Maximum Current: 10 mA
Resistance Measurement Range: 1 x 10
3
to 2 x 10
16
Ω
Operating Temperature: 0°C to 55°C
DUT Size: For Alligator Clip and Flat Table, lead diame-
ter ≤5 mm
Furnished Accessories:
Compensation and Measurement: Open compensation
is recommended before measurement. When using the
axial lead module, have no DUT connected to the elec-
trodes. When using the SMD module, separate the high
and low electrodes from each other. The separation
should be equivalent in size to the DUT’s width. When
using the alligator clip and flat table, remove the alligator
clips from the input terminals of the test fixture. After
preparing the open condition of the respective module,
close the top cover and then perform open compensation.
Finally, the DUT is inserted into the respective module.
The following figure shows the three component modules.
Type Connector
Input Triaxial (special screw-type)
Output High Voltage BNC (special type)
Control Interlock connector*
4339B with 16339A
SMD module
Description P/N Qty.
Axial Lead Module 16339-60102 1
SMD Module 16339-60101 1
Flat Table 16339-60004 1
Miniature Banana-Plug cable 16339-61621 2
100 kΩ Output Resistor 16339-61001 1
1 MΩ Output Resistor 16339-61002 1
10 MΩ Output Resistor 16339-61003 1
100 MΩ Output Resistor 16339-61004 1
Alligator Clip 8710-1984 2
Carrying Case 16339-60021 1
Operation and Service Manual 16339-90010 1
Component module configurations
SMD module Axial Lead module Alligator clip and Flat table
DUT Dimensions
- Accessories Selection Guide 1
- For Impedance Measurements 1
- Table of Contents 2
- Introduction 5
- 6. Furnished Accessories 8
- 7. Terminal Adapters 9
- 16085B Terminal Adapter 9
- 42942A Terminal Adapter 9
- Accessories Catalogue 10
- Applicable Instrument 12
- 16047A Test Fixture 13
- P/N 5000-4226 13
- Lead Components 14
- 16034E Test Fixture 17
- 16034G Test Fixture 18
- 16034H Test Fixture 19
- 16044A Test Fixture 20
- Electrode dimensions 21
- 16334A Tweezers Contact 22
- Test Fixture 22
- 16043-60011/12 23
- 3-Terminal SMD Test Fixture 23
- Other Components 26
- Port/Cable Extension 29
- 4-Terminal Converter 32
- 42941A Impedance Probe Kit 33
- Bias Fixture 34
- 16065C 40Vdc External 34
- Voltage Bias Adapter 34
- 42841A Bias Current Source 35
- Description P/N Qty 36
- Shorting Plate 42842-00607 1 36
- Protection Caps N/A 2 37
- 42851-61100 SMD Test Fixture 38
- 42843A Bias Current Cable 39
- Furnished Accessories: 42
- Electrode gap (mm) A (%) 44
- 0.3 0.005 × M.R.P 44
- 0.5 0.006 × M.R.P 44
- 1.0 0.008 × M.R.P 44
- 2.0 0.020 × M.R.P 44
- Up to 3 GHz (7 mm) 46
- 16092A Spring Clip Fixture 47
- Shorting Plate 16092-08010 1 48
- Up to 3 GHz (7 mm) SMD 50
- Up to 3 GHz (7 mm) Probe 66
- Up to 3 GHz (7 mm) Material 68
- DC (High resistance) 71
- 16339A Component Test Fixture 72
- DC (High resistance) SMD 73
- 16117B Low Noise Test Leads 74
- 16117E Low Noise Test Leads 75
- 16117C Low Noise Test Leads 75
- DC (High resistance) Material 76
- 1 kHz (Milliohm) 78
- 16338A Test Lead Kit 79
- 16143-60011 Mating Cable 80
- 16005-60011 Kelvin Clip Leads 80
- 16007-60001/2 Kelvin 81
- Alligator Clip Leads 81
- 16006-60001 Pin-type Leads 81
- Other Accessories 82
- Appendix Additional Error 87
- Specifications of 91
- Short Repeatability 91
- Actual Measurement 91
- Appendix Compensation 93
- Test accessories/fixtures 100
- Agilent Web Resources 102
- Remove all doubt 104
Related products and manuals for Cable network testers Agilent Technologies 16048A
(104 pages)© 2020, manymanuals.com. All rights reserved. | 0.936 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals