Agilent Technologies 4294A Service Manual Page 157
- Page / 249
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7 149
Service Related Menus
DIAGNOSTIC TEST Menu
7. Service Related Menus
Figure 7-1 Test Status on the Display
To see the test status of the desired test, enter the desired test number using the numeric
keypad, [↑], [↓], or RPG knob. Also, the GPIB commands listed below are available to get
the status using GPIB.
:DIAG:TEST:RES? <numeric> returns the test status. The <numeric> specifies
the test number and is an integer from 0 to 31.
*TST? executes internal test 0: ALL INTERNAL and
returns the test result.
Table 7-1 shows the test status abbreviation, its definition, and the GPIB test status code.
Table 7-1 Te s t Status Terms
Status Abbreviation Definition GPIB Code
PASS Pass “PASS”
FAIL Fail “FAIL”
BUSY In progress “BUSY”
NDON Not done “NDON”
DONE Done “DONE”
The test status is not stored in nonvolatile memory (battery backup memory). When the
analyzer is turned off and on, the analyzer sets test status abbreviation except the power-on
self test (internal tests 5 to 16) to “NDONE” (Not done). If a test is aborted by pressing any
key during its execution, the test status is undefined.
Test Descriptions
This section describes all 31 diagnostic tests.
- Manual Change 1
- Change 2 2
- OSC Level Accuracy Test 2
- Service Manual 9
- Manual Printing History 10
- Safety Summary 11
- Safety Symbol 12
- Certification 12
- Warranty 13
- Limitation of Warranty 13
- Exclusive Remedies 13
- Assistance 13
- Typeface Conventions 14
- Contents 15
- 1 General Information 21
- [System] 22
- Require Equipment 24
- *3.furnished with the 4294A 25
- General Information 26
- 2 Performance Test 27
- Performance Test 28
- Frequency Accuracy Test 29
- Specification 29
- Test Equipment 29
- [Center] - [1] - [M/μ] 34
- [Center] - [1] - [M/m] 37
- DC Bias Monitor Accuracy Test 39
- DC Bias Level Accuracy Test 43
- Measurement Accuracy Test 46
- Capacitor) Setting 50
- Resister) Setting 51
- Standard Capacitor) Setting 57
- Standard Resistor) Setting 57
- [Cal] - FIXTURE COMPEN - OPEN 58
- Calculation Sheet 60
- Performance Test Record 76
- 3 Adjustment 89
- Safety Considerations 90
- Required Controller 90
- Warm-up for Adjustment 90
- Order of Adjustment 91
- Equipment Setup 92
- Required Equipment 100
- Procedure 100
- Adjustment 110
- 4 Troubleshooting 113
- TROUBLESHOOTING SUMMARY 114
- 4. Troubleshooting 115
- Troubleshooting 115
- START HERE 116
- INSPECT THE POWER ON SEQUENCE 117
- Check the GPIB Interface 118
- Check the Parallel Interface 118
- Check the Power-On Selftest 119
- Execute All Internal Tests 119
- Execute the Individual Test 119
- Null Detector Offset CC 123
- 5. Power Supply 125
- INTRODUCTION 126
- 3.Check the A50 Five LEDs 129
- 4. Check the A1 +5 VD LED 129
- 5. Check the A9 Two LEDs 130
- Power Supply Troubleshooting 132
- 3. Check the A50 SHUTDOWN LED 134
- 2. Remove A50 135
- 3. Remove Assemblies 135
- STEADILY 136
- CONVERTER 139
- Table 5-1 A50 Power Supplies 140
- 6. Digital Control 141
- A1 CPU Replacement 144
- FIRMWARE INSTALLATION 145
- 2. Check the A1 CPU 149
- 6. Check the A53 FDD 151
- 8. Check the 24 BIT I/O PORT 151
- 9. Check the LAN Operation 152
- 7 Service Related Menus 155
- DIAGNOSTIC TEST Menu 156
- Test Descriptions 157
- Service Related Menus 162
- 8 Theory of Operation 163
- OVERALL OPERATION 164
- POWER SUPPLY OPERATION 166
- Line Power Module 167
- A40 Preregulator 168
- A50 DC-DC Converter 168
- A50 Shutdown LED 168
- A9 Floating Power Supply 168
- DIGITAL CONTROL OPERATION 169
- Theory of Operation 170
- A30 Front Keyboard 171
- A32 I-BASIC Interface 171
- A34 I/O Connector 171
- A54 Inverter 172
- SOURCE THEORY 173
- A2 Hc Amp 174
- TRANSDUCER THEORY 175
- A3 Hp Amp 176
- A4 Lc Amp 176
- A5 IV Converter & Lp Amp 176
- A6 Vector Generator 176
- VECTOR RATIO DETECTOR THEORY 177
- 9 Parts Replacement 180
- Replaceable Part List 181
- Parts List 182
- Parts Replacement 183
- Table 9-4 Top View (Shield) 188
- 4TP Assembly 189
- Table 9-8 Front Assembly 1 193
- Table 9-9 Front Assembly 2 194
- Table 9-10 Front Assembly 3 195
- Table 9-12 Front Assembly 5 197
- Table 9-13 Front Assembly 6 198
- Table 9-14 Front Assembly 7 199
- Table 9-15 Front Assembly 8 200
- Table 9-16 Front Assembly 9 201
- Table 9-17 Front Assembly 10 202
- Table 9-18 Rear Assembly 1 203
- Table 9-19 Rear Assembly 2 204
- Figure 9-21 Rear Assembly 3 205
- Table 9-20 Rear Assembly 3 206
- Table 9-21 Rear Assembly 4 207
- Table 9-22 Rear Assembly 5 208
- Table 9-23 Side View 209
- Table 9-24 Chassis Assembly 210
- Table 9-25 Other Parts 211
- Replacement Procedure 212
- Front Panel Removal 213
- Rear Panel Removal 213
- A1 CPU Board Replacement 214
- A2/A8/A50/A51 Replacement 214
- A3 Hp Amplifier Replacement 214
- A4 Lc Amplifier Replacement 215
- A7 Synthesizer Replacement 216
- A53 FDD Removal 217
- A52 LCD Removal 218
- A40 Preregulator Replacement 218
- Power Switch Replacement 219
- 10 Post Repair Procedures 222
- POST REPAIR PROCEDURES 223
- 216 10 225
- Post Repair Procedures 225
- A Manual Changes 226
- Manual Changes 227
- B Power Requirement 228
- Replacing Fuse 229
- Power Requirements 230
- 222 Appendix B 231
- Power Requirement 231
- C Error messages 232
- Order of Alphabet 233
- 240 Appendix C 249
- Error messages 249
Related products and manuals for Multimeters Agilent Technologies 4294A
(116 pages)© 2020, manymanuals.com. All rights reserved. | 1.930 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals