Agilent Technologies 4294A Instruction Manual download pdf (Page 387)

Appendix B 379

Key Definitions

Softkeys displayed by pressing the [Cal] key

B. Key Definitions

SETUP ä Displays Table B-36, “Adapter setup (Adapter Setup) menu,” on page 379. If

you select an adapter configuration corresponding to a key other than the NONE

key (HP 16047E test fixture, etc.), you have to enter this menu when you use the

adapter (4TP 1M, 4TP 2M, 7mm 42942A, PROBE 42941A) for the first time

and measure the calibration standard. The setup data of adapters once set up are

stored in the internal non-volatile memory of the 4294A, and therefore re-setup

is not required under normal conditions. If the NONE key is selected as the

adapter configuration, this SETUP key is invalid (setup is not required).

(N/A)

return Returns to Table B-34, “Calibration (Calibration) menu,” on page 378. (N/A)

Table B-36 Adapter setup (Adapter Setup) menu

Key operation: [Cal] - ADAPTER [ ] - SETUP

Softkey Function GPIB command

PHASE COMP [ ] Executes the measurement of the phase compensation data. The content of [ ] is -

before the data acquisition and changes to DONE after the data acquisition. If the

4TP 1M key, 4TP 2M key, 7mm 42942A key, or PROBE 42941A key has been

selected in Table B-35, “Adapter configuration (Adapter) menu,” on page 378,

this phase compensation data must be measured.

ECALP

OPEN [ ] Executes the measurement of the OPEN data. The content of [ ] is - before the

data acquisition and changes to DONE after the data acquisition. If the 7mm

42942A key or PROBE 42941A key has been selected in Table B-35, “Adapter

configuration (Adapter) menu,” on page 378, this OPEN data must be measured.

Otherwise, the measurement of the OPEN data is not required (OPEN [ ] key is

invalid).

ECALA

SHORT [ ] Executes the measurement of the SHORT data. The content of [ ] is - before the

data acquisition and changes to DONE after the data acquisition. If the

7mm 42942A key or PROBE 42941A key has been selected in Table B-35,

“Adapter configuration (Adapter) menu,” on page 378, this SHORT data must

be measured. Otherwise, the measurement of the SHORT data is not required

(SHORT [ ] key is invalid).

ECALB

LOAD [ ] Executes the measurement of the LOAD data. The contents of [ ] is - before the

data acquisition, and changes to DONE after the data acquisition. If the 4TP 1M

key, 4TP 2M key, 7mm 42942A key, or PROBE 42941A key has been selected

in Table B-35, “Adapter configuration (Adapter) menu,” on page 378, this

LOAD data must be measured.

ECALC

done Based on the above acquired data, calculates the setup data for the selected

adapter and stores it in the internal non-volatile memory of the 4294A. For

adapters whose setup data is once acquired, re-setup is not required under normal

conditions. Executing this key returns to Table B-35, “Adapter configuration

(Adapter) menu,” on page 378.

ECALDON

cancel Cancels the setup for the selected adapter and returns to Table B-35, “Adapter

configuration (Adapter) menu,” on page 378. Setup data previously executed is

valid.

ECALQUI

Table B-35 Adapter configuration (Adapter) menu

Key operation: [Cal] - ADAPTER [ ]

Softkey Function GPIB command

1 2 ... 382 383 384 385 386 387 388 389 390 391 392 ... 468 469

Comments to this Manuals

No comments

Agilent Technologies 4294A Instruction Manual Page 387

Comments to this Manuals

Related products and manuals for Multimeters Agilent Technologies 4294A