Agilent Technologies 4294A Instruction Manual download pdf (Page 418)

410 Appendix B

Key Definitions

Softkeys displayed by pressing the [System] key

MIDDLE VALUE Sets the limit center value of the measured value at the sweep start point of the

segment

. When setting the center value, also set the difference value (difference

between upper and the lower limits) with the DELTA LIMIT key. This kind of

limit configuration set by the center value and the difference value can be used as

an alternative to a limit configuration set by the upper and lower limits.

LIMVSTAR <value>

DELTA LIMIT Sets the limit difference value of the measured value at the sweep start point of

the segment

. When setting the difference value, also set the center value with

the MIDDLE VALUE key. This kind of limit configuration set by the center

value and the difference value can be used as an alternative to a limit

configuration set by the upper and lower limits.

LIMDSTAR <value>

more 1/3 Displays Table B-85, “Segment edit (Edit Limit) menu (2/3),” on page 410. (N/A)

done Finishes the editing of the segment, replaces the segment before the editing with

the new segment, and stores it. Also, returns to Table B-83, “Limit line edit (Edit

Limit) menu,” on page 409.

LIMSDON

cancel Cancels the editing of the segment and returns to Table B-83, “Limit line edit

(Edit Limit) menu,” on page 409. The segment before the editing remains

unchanged.

LIMSQUI

1. Even if you have set the limits with the MIDDLE VALUE (center value) key and the DELTA LIMIT (difference value) key, you

can convert the table into the upper and lower limit format by pressing the UPPER LIMIT key or the LOWER LIMIT key. On

the other hand, even if you have set the limits with the UPPER LIMIT (upper limit) key and the LOWER LIMIT (lower limit)

key, you can convert the table into the center and difference value format by pressing the MIDDLE VALUE key or the DELTA

LIMIT key.

Table B-85 Segment edit (Edit Limit) menu (2/3)

Key operation: [System] - LIMIT TEST - EDIT LIMIT LINE - EDIT - more 1/3

[System] - LIMIT TEST - EDIT LIMIT LINE - ADD - more 1/3

Softkey Function GPIB command

STOP Sets the sweep stop value of the segment. LIMSTOP <value>

UPPER LIMIT Sets the upper limit of the measured value at the sweep stop point of the

segment

. Be sure to set both the upper and lower limits. If an upper limit is not

required, set an extremely large value (for example, 1G) as the upper limit. If you

set the upper limit smaller than the lower limit, both limits are set to the newly

entered value automatically.

LIMUSTOP <value>

LOWER LIMIT Sets the lower limit of the measured value at the sweep stop point of the

segment

. Be sure to set both the upper and lower limits. If a lower limit is not

required, set an extremely small value (for example, -1G) as the lower limit. If

you set the lower limit greater than the upper limit, both limits are set to the

newly entered value automatically.

LIMLSTOP <value>

MIDDLE VALUE Sets the limit center value of the measured value at the sweep stop point of the

segment

. When setting the center value, also set the difference value (difference

between the upper and lower limits) with the DELTA LIMIT key. This kind of

limit configuration set by the center value and the difference value can be used as

an alternative to the limit configuration set by the upper and lower limits.

LIMVSTOP <value>

Table B-84 Segment edit (Edit Limit) menu (1/3)

Key operation: [System] - LIMIT TEST - EDIT LIMIT LINE - EDIT

[System] - LIMIT TEST - EDIT LIMIT LINE - ADD

Softkey Function GPIB command

1 2 ... 413 414 415 416 417 418 419 420 421 422 423 ... 468 469

Comments to this Manuals

No comments

Agilent Technologies 4294A Instruction Manual Page 418

Comments to this Manuals

Related products and manuals for Multimeters Agilent Technologies 4294A