Agilent Technologies N8201A Service Manual Page 265
- Page / 332
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Basic Function Commands 8
Agilent N8211A/N8212A Performance Upconverter Synthetic Instrument Module, 250 kHz to 20 / 40 GHz 265
OFF (0) eliminates the power discontinuity normally associated with the attenuator
switching during power adjustments. During an amplitude sweep operation,
N8211A/N8212As with Option 1E1 protect the step attenuator by automatically switching
to attenuator hold mode (ON). The attenuator is locked at its current setting and the
amplitude sweep range is limited to 40 dB.
Example
:POW:ATT:AUTO OFF
The example turns off the attenuator hold function.
*RST 1
:MODE
Supported All
[:SOURce]:POWer:MODE FIXed|SWEep|LIST
[:SOURce]:POWer:MODE?
Starts or stops an amplitude sweep and sets the power mode of the N8211A/N8212A.
FIXed Stops a power sweep and allows the N8211A/N8212A to operate at a fixed power
level. Refer to “[:LEVel][:IMMediate][:AMPLitude]" on page 269 for more information on
running power sweeps and setting CW amplitude settings that control the output power.
SWEep The effects of this choice are determined by the sweep generation type selected
(refer to “:SWEep:GENeration” on page 127). If you are using analog sweep generation, the
current ramp sweep amplitude settings (start and stop) control the output power. If you are
using step sweep generation, the current step sweep amplitude settings control the output
power. In both cases, this selection also activates the sweep. This choice is available with
Option 007 only.
LIST Selects the swept power mode. If sweep triggering is set to immediate along with
continuous sweep mode, executing the command starts the LIST or STEP frequency sweep.
To perform a frequency and amplitude sweep, you must also select LIST or SWEep as the
frequency mode (see “:FREQuency:MODE" on page 234).
Example
:POW:MODE LIST
The example sets list as the amplitude sweep mode.
*RST FIX
- SCPI Programming Guide 1
- Adobe Acrobat Reader 2
- Contents 5
- 6SCPI Basics 7
- 8 Basic Function Commands 11
- 9 Analog Commands 13
- LAN Interface 19
- Agilent IO Libraries Suite 20
- Programming Languages 22
- Error Messages 23
- Using the LAN Interface 25
- Using LAN 26
- Using the LAN Interface 2 27
- 2 Using the LAN Interface 28
- 2 Turn on power to the PC 29
- Verifying LAN Functionality 31
- Using VXI-11 33
- Using Telnet LAN 34
- Using FTP 36
- Troubleshooting 37
- Right-Pane Functions 38
- Left-Pane Functions 38
- From a DOS Window 45
- From the PCs Control Panel 45
- If the LAN LED is Red 46
- Programming Examples 51
- Running C++ Programs 52
- Running C# Examples 53
- Running Basic Examples 53
- Running Java Examples 53
- Running Perl Examples 54
- VXI-11 Programming 55
- 3 Programming Examples 56
- Programming Examples 3 57
- Sockets LAN Programming and C 60
- Sockets on UNIX 61
- Sockets on Windows 62
- Queries for Lan Using Sockets 63
- Programming the 97
- Register System 97
- Status Register Bit Values 101
- Determining What to Monitor 102
- Deciding How to Monitor 102
- The polling method 103
- Generating a Service Request 104
- Status Register SCPI Commands 105
- Status Byte Group 107
- Status Byte Register 108
- *SRE <data> command 109
- Status Groups 110
- Bit Description 116
- Agilent Technologies 131
- Overview 132
- Save and Recall SCPI Commands 133
- SCPI Basics 153
- SCPI Listings 154
- 6 SCPI Basics 156
- Command Types 157
- Command Tree 158
- Numeric Parameters 159
- Extended Numeric Parameters 160
- Discrete Parameters 160
- Boolean Parameters 161
- String Parameters 161
- Real Response Data 161
- Integer Response Data 162
- Discrete Response Data 162
- Numeric Boolean Response Data 162
- String Response Data 162
- Program Messages 163
- File Name Variables 164
- C the binary waveform data 165
- #B101101 binary equivalent 167
- #H2D hexadecimal equivalent 167
- #Q55 octal equivalent 167
- System Commands 169
- 7 System Commands 170
- :IQ:DEFault 171
- :IQ:FULL 171
- :IQ:STARt 171
- :IQ:STOP 172
- :WBIQ:DC 172
- :WBIQ:DEFault 173
- :WBIQ:FULL 173
- :WBIQ:STARt 173
- :WBIQ:STOP 174
- :CCOunt:ATTenuator 175
- :CCOunt:PON 175
- :DISPlay:OTIMe 175
- :LICENse:AUXiliary 175
- :OPTions 176
- :OPTions:DETail 176
- :REVision 176
- Display Subsystem (:DISPlay) 177
- IEEE 488.2 Common Commands 178
- Supported All 179
- System Commands 7 181
- Low-Band Filter Subsystem 184
- Memory Subsystem (:MEMory) 185
- :CATalog[:ALL] 186
- :COPY[:NAME] 186
- :DATA:APPend 186
- :DELete:ALL 187
- :DELete:BINary 187
- :DELete:LIST 188
- :DELete:STATe 188
- :DELete:UFLT 188
- :DELete[:NAME] 188
- :FREE[:ALL] 188
- :LOAD:LIST 189
- :STATe:COMMent 189
- :STORe:LIST 190
- :CATalog 191
- :HEADer:CLEar 192
- :HEADer:DESCription 193
- Output Subsystem (:OUTPut) 195
- :MODulation[:STATe] 196
- [:STATe] 196
- Status Subsystem (:STATus) 197
- :OPERation:NTRansition 198
- :OPERation:PTRansition 198
- :OPERation[:EVENt] 199
- :QUEStionable:CONDition 201
- :QUEStionable:ENABle 202
- Range 0–32767 203
- :QUEStionable:NTRansition 207
- :QUEStionable:POWer:CONDition 207
- :QUEStionable:POWer:ENABle 207
- :QUEStionable:POWer[:EVENt] 209
- :QUEStionable:PTRansition 209
- :QUEStionable[:EVENt] 210
- System Subsystem (:SYSTem) 211
- :ERRor:SCPI[:SYNTax] 212
- :ERRor[:NEXT] 212
- :OEMHead:FREQuency:STARt 213
- :OEMHead:FREQuency:STOP 213
- :OEMHead:SELect 213
- :OEMHead:FREQuency:MULTiplier 215
- :PON:TYPE 215
- :PRESet:ALL 216
- :PRESet:PERSistent 216
- :PRESet:PN9 216
- :PRESet:TYPE 217
- :PRESet[:USER]:SAVE 217
- :SECurity:ERASeall 217
- :SECurity:LEVel 217
- :SECurity:LEVel:STATe 218
- :SECurity:OVERwrite 219
- :SECurity:SANitize 219
- :VERSion 220
- Trigger Subsystem 221
- :TRIGger:OUTPut:POLarity 222
- :TRIGger[:SEQuence]:SLOPe 222
- :TRIGger[:SEQuence]:SOURce 222
- *RST IMM 223
- Unit Subsystem (:UNIT) 224
- Basic Function Commands 225
- :FLATness:LOAD 226
- :FLATness:PAIR 226
- :FLATness:POINts 227
- :FLATness:PRESet 227
- :FLATness:STORe 227
- :FREQuency:CENTer 229
- :FREQuency:CHANnels:BAND 229
- :FREQuency:CHANnels:NUMBer 231
- :FREQuency:CHANnels[:STATe] 232
- :FREQuency:FIXed 232
- :FREQuency:MANual 233
- :FREQuency:MODE 234
- :FREQuency:MULTiplier 235
- :FREQuency:OFFSet 235
- :FREQuency:OFFSet:STATe 236
- :FREQuency:REFerence 236
- :FREQuency:REFerence:SET 236
- :FREQuency:REFerence:STATe 237
- :FREQuency:SPAN 237
- :FREQuency:STARt 238
- :FREQuency:STOP 238
- :FREQuency[:CW] 239
- :PHASe:REFerence 240
- :PHASe[:ADJust] 240
- :ROSCillator:SOURce 241
- :ROSCillator:SOURce:AUTO 241
- :LIST:DIRection 243
- :LIST:DWELl 244
- :LIST:DWELl:POINts 244
- :LIST:DWELl:TYPE 245
- :LIST:FREQuency 245
- :LIST:FREQuency:POINts 246
- :LIST:MANual 246
- :LIST:MODE 247
- :LIST:POWer 247
- :LIST:POWer:POINts 248
- :LIST:RETRace 248
- :LIST:TRIGger:SOURce 248
- :LIST:TYPE 249
- :SWEep:CONTrol:STATe 250
- :SWEep:CONTrol:TYPE 250
- :SWEep:DWELl 251
- :SWEep:GENeration 251
- :SWEep:MODE 252
- :SWEep:POINts 252
- SWEep:TIME 253
- :SWEep:TIME:AUTO 253
- :MARKer:AMPLitude[:STATe] 255
- :MARKer:AMPLitude:VALue 255
- :MARKer:AOFF 255
- :MARKer:DELTa? 256
- :MARKer:MODe 257
- :MARKer:REFerence 257
- :ALC:BANDwidth 259
- :ALC:BANDwidth 259
- :ALC:LEVel 260
- :ALC:SEARch 260
- :ALC:SEARch:REFerence 261
- :ALC:SEARch:SPAN:START 261
- :ALC:SEARch:SPAN:STOP 261
- :ALC:SOURce 262
- :ALC:SOURce:EXTernal:COUPling 263
- :ALC[:STATe] 263
- :ATTenuation 264
- :ATTenuation:AUTO 264
- Basic Function Commands 8 265
- :PROTection:STATe 266
- :REFerence 266
- :REFerence:STATe 267
- [:LEVel][:IMMediate]:OFFSet 268
- Range See data sheet 269
- Analog Commands 271
- :AM[1] 272
- :AM:MODE 273
- :AM:WIDeband:SENSitivity 273
- :AM:WIDeband:STATe 274
- *RST +5.00000000E+001 275
- Supported Option UNT 275
- *RST +4.00000000E+002 275
- Analog Commands 9 277
- :AM[1] 278
- :AM[1] 279
- :AM[1] 279
- :AM[1] 280
- :AM[1] 280
- :AM[:DEPTh]:STEP[:INCRement] 281
- :FM[1] 283
- *RST UNIF 287
- :FM[1] 288
- :FM[1] 289
- :FM[1] 289
- :FM[1] 290
- :LFOutput:AMPLitude 291
- DC 293
- :FUNCtion[1]:SWEep:TRIGger 294
- :LFOutput:SOURce 295
- :LFOutput:STATe 295
- :PM[1] 297
- :PM[1] 298
- :PM[1] 303
- :PM[1] 303
- :PM[1] 304
- :PM[1] 305
- :PULM:INTernal[1]:DELay 307
- :PULM:INTernal[1]:DELay:STEP 308
- :PULM:INTernal[1]:FREQuency 308
- :PULM:INTernal[1]:PERiod 309
- :PULM:INTernal[1]:PWIDth 310
- :PULM:INTernal[1]:PWIDth:STEP 311
- :PULM:INTernal 311
- :PULM:SOURce 312
- :PULM:STATe 312
- Digital Modulation Commands 313
- :EXTernal:Filter 314
- :EXTernal:Filter:AUTO 314
- :EXTernal:HCRest 315
- :EXTernal:POLarity 315
- :EXTernal:SOURce 315
- :IQADjustment:DELay 316
- :IQADjustment:EXTernal:GAIN 318
- :IQADjustment:GAIN 320
- :IQADjustment:IOFFset 321
- :IQADjustment:QOFFset 321
- :IQADjustment:QSKew 322
- :IQADjustment:SKEW 322
- :IQADjustment:SKEW:Path 323
- :IQADjustment[:STATe] 324
- :MODulation:ATTen 324
- :MODulation:ATTen:AUTO 325
- :MODulation:ATTen:EXTernal 325
- :MODulation:FILTer 327
- :MODulation:FILTer:AUTO 327
- :POLarity[:ALL] 328
- :SKEW:PATH 328
- :SKEW[:STATe] 329
- Supported N8212A 330
- *RST +0.00000000E+000 330
Related products and manuals for Video converters Agilent Technologies N8201A
(190 pages)© 2020, manymanuals.com. All rights reserved. | 0.521 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals